| 1 |
.. SPDX-License-Identifier: GPL-2.0 |
| 2 |
.. include:: <isonum.txt> |
| 3 |
|
| 4 |
=============================== |
| 5 |
Marvell(Aquantia) AQtion Driver |
| 6 |
=============================== |
| 7 |
|
| 8 |
For the aQuantia Multi-Gigabit PCI Express Family of Ethernet Adapters |
| 9 |
|
| 10 |
.. Contents |
| 11 |
|
| 12 |
- Identifying Your Adapter |
| 13 |
- Configuration |
| 14 |
- Supported ethtool options |
| 15 |
- Command Line Parameters |
| 16 |
- Config file parameters |
| 17 |
- Support |
| 18 |
- License |
| 19 |
|
| 20 |
Identifying Your Adapter |
| 21 |
======================== |
| 22 |
|
| 23 |
The driver in this release is compatible with AQC-100, AQC-107, AQC-108 |
| 24 |
based ethernet adapters. |
| 25 |
|
| 26 |
|
| 27 |
SFP+ Devices (for AQC-100 based adapters) |
| 28 |
----------------------------------------- |
| 29 |
|
| 30 |
This release tested with passive Direct Attach Cables (DAC) and SFP+/LC |
| 31 |
Optical Transceiver. |
| 32 |
|
| 33 |
Configuration |
| 34 |
============= |
| 35 |
|
| 36 |
Viewing Link Messages |
| 37 |
--------------------- |
| 38 |
Link messages will not be displayed to the console if the distribution is |
| 39 |
restricting system messages. In order to see network driver link messages on |
| 40 |
your console, set dmesg to eight by entering the following:: |
| 41 |
|
| 42 |
dmesg -n 8 |
| 43 |
|
| 44 |
.. note:: |
| 45 |
|
| 46 |
This setting is not saved across reboots. |
| 47 |
|
| 48 |
Jumbo Frames |
| 49 |
------------ |
| 50 |
The driver supports Jumbo Frames for all adapters. Jumbo Frames support is |
| 51 |
enabled by changing the MTU to a value larger than the default of 1500. |
| 52 |
The maximum value for the MTU is 16000. Use the `ip` command to |
| 53 |
increase the MTU size. For example:: |
| 54 |
|
| 55 |
ip link set mtu 16000 dev enp1s0 |
| 56 |
|
| 57 |
ethtool |
| 58 |
------- |
| 59 |
The driver utilizes the ethtool interface for driver configuration and |
| 60 |
diagnostics, as well as displaying statistical information. The latest |
| 61 |
ethtool version is required for this functionality. |
| 62 |
|
| 63 |
NAPI |
| 64 |
---- |
| 65 |
NAPI (Rx polling mode) is supported in the atlantic driver. |
| 66 |
|
| 67 |
Supported ethtool options |
| 68 |
========================= |
| 69 |
|
| 70 |
Viewing adapter settings |
| 71 |
------------------------ |
| 72 |
|
| 73 |
:: |
| 74 |
|
| 75 |
ethtool <ethX> |
| 76 |
|
| 77 |
Output example:: |
| 78 |
|
| 79 |
Settings for enp1s0: |
| 80 |
Supported ports: [ TP ] |
| 81 |
Supported link modes: 100baseT/Full |
| 82 |
1000baseT/Full |
| 83 |
10000baseT/Full |
| 84 |
2500baseT/Full |
| 85 |
5000baseT/Full |
| 86 |
Supported pause frame use: Symmetric |
| 87 |
Supports auto-negotiation: Yes |
| 88 |
Supported FEC modes: Not reported |
| 89 |
Advertised link modes: 100baseT/Full |
| 90 |
1000baseT/Full |
| 91 |
10000baseT/Full |
| 92 |
2500baseT/Full |
| 93 |
5000baseT/Full |
| 94 |
Advertised pause frame use: Symmetric |
| 95 |
Advertised auto-negotiation: Yes |
| 96 |
Advertised FEC modes: Not reported |
| 97 |
Speed: 10000Mb/s |
| 98 |
Duplex: Full |
| 99 |
Port: Twisted Pair |
| 100 |
PHYAD: 0 |
| 101 |
Transceiver: internal |
| 102 |
Auto-negotiation: on |
| 103 |
MDI-X: Unknown |
| 104 |
Supports Wake-on: g |
| 105 |
Wake-on: d |
| 106 |
Link detected: yes |
| 107 |
|
| 108 |
|
| 109 |
.. note:: |
| 110 |
|
| 111 |
AQrate speeds (2.5/5 Gb/s) will be displayed only with linux kernels > 4.10. |
| 112 |
But you can still use these speeds:: |
| 113 |
|
| 114 |
ethtool -s eth0 autoneg off speed 2500 |
| 115 |
|
| 116 |
Viewing adapter information |
| 117 |
--------------------------- |
| 118 |
|
| 119 |
:: |
| 120 |
|
| 121 |
ethtool -i <ethX> |
| 122 |
|
| 123 |
Output example:: |
| 124 |
|
| 125 |
driver: atlantic |
| 126 |
version: 5.2.0-050200rc5-generic-kern |
| 127 |
firmware-version: 3.1.78 |
| 128 |
expansion-rom-version: |
| 129 |
bus-info: 0000:01:00.0 |
| 130 |
supports-statistics: yes |
| 131 |
supports-test: no |
| 132 |
supports-eeprom-access: no |
| 133 |
supports-register-dump: yes |
| 134 |
supports-priv-flags: no |
| 135 |
|
| 136 |
|
| 137 |
Viewing Ethernet adapter statistics |
| 138 |
----------------------------------- |
| 139 |
|
| 140 |
:: |
| 141 |
|
| 142 |
ethtool -S <ethX> |
| 143 |
|
| 144 |
Output example:: |
| 145 |
|
| 146 |
NIC statistics: |
| 147 |
InPackets: 13238607 |
| 148 |
InUCast: 13293852 |
| 149 |
InMCast: 52 |
| 150 |
InBCast: 3 |
| 151 |
InErrors: 0 |
| 152 |
OutPackets: 23703019 |
| 153 |
OutUCast: 23704941 |
| 154 |
OutMCast: 67 |
| 155 |
OutBCast: 11 |
| 156 |
InUCastOctects: 213182760 |
| 157 |
OutUCastOctects: 22698443 |
| 158 |
InMCastOctects: 6600 |
| 159 |
OutMCastOctects: 8776 |
| 160 |
InBCastOctects: 192 |
| 161 |
OutBCastOctects: 704 |
| 162 |
InOctects: 2131839552 |
| 163 |
OutOctects: 226938073 |
| 164 |
InPacketsDma: 95532300 |
| 165 |
OutPacketsDma: 59503397 |
| 166 |
InOctetsDma: 1137102462 |
| 167 |
OutOctetsDma: 2394339518 |
| 168 |
InDroppedDma: 0 |
| 169 |
Queue[0] InPackets: 23567131 |
| 170 |
Queue[0] OutPackets: 20070028 |
| 171 |
Queue[0] InJumboPackets: 0 |
| 172 |
Queue[0] InLroPackets: 0 |
| 173 |
Queue[0] InErrors: 0 |
| 174 |
Queue[1] InPackets: 45428967 |
| 175 |
Queue[1] OutPackets: 11306178 |
| 176 |
Queue[1] InJumboPackets: 0 |
| 177 |
Queue[1] InLroPackets: 0 |
| 178 |
Queue[1] InErrors: 0 |
| 179 |
Queue[2] InPackets: 3187011 |
| 180 |
Queue[2] OutPackets: 13080381 |
| 181 |
Queue[2] InJumboPackets: 0 |
| 182 |
Queue[2] InLroPackets: 0 |
| 183 |
Queue[2] InErrors: 0 |
| 184 |
Queue[3] InPackets: 23349136 |
| 185 |
Queue[3] OutPackets: 15046810 |
| 186 |
Queue[3] InJumboPackets: 0 |
| 187 |
Queue[3] InLroPackets: 0 |
| 188 |
Queue[3] InErrors: 0 |
| 189 |
|
| 190 |
Interrupt coalescing support |
| 191 |
---------------------------- |
| 192 |
|
| 193 |
ITR mode, TX/RX coalescing timings could be viewed with:: |
| 194 |
|
| 195 |
ethtool -c <ethX> |
| 196 |
|
| 197 |
and changed with:: |
| 198 |
|
| 199 |
ethtool -C <ethX> tx-usecs <usecs> rx-usecs <usecs> |
| 200 |
|
| 201 |
To disable coalescing:: |
| 202 |
|
| 203 |
ethtool -C <ethX> tx-usecs 0 rx-usecs 0 tx-max-frames 1 tx-max-frames 1 |
| 204 |
|
| 205 |
Wake on LAN support |
| 206 |
------------------- |
| 207 |
|
| 208 |
WOL support by magic packet:: |
| 209 |
|
| 210 |
ethtool -s <ethX> wol g |
| 211 |
|
| 212 |
To disable WOL:: |
| 213 |
|
| 214 |
ethtool -s <ethX> wol d |
| 215 |
|
| 216 |
Set and check the driver message level |
| 217 |
-------------------------------------- |
| 218 |
|
| 219 |
Set message level |
| 220 |
|
| 221 |
:: |
| 222 |
|
| 223 |
ethtool -s <ethX> msglvl <level> |
| 224 |
|
| 225 |
Level values: |
| 226 |
|
| 227 |
====== ============================= |
| 228 |
0x0001 general driver status. |
| 229 |
0x0002 hardware probing. |
| 230 |
0x0004 link state. |
| 231 |
0x0008 periodic status check. |
| 232 |
0x0010 interface being brought down. |
| 233 |
0x0020 interface being brought up. |
| 234 |
0x0040 receive error. |
| 235 |
0x0080 transmit error. |
| 236 |
0x0200 interrupt handling. |
| 237 |
0x0400 transmit completion. |
| 238 |
0x0800 receive completion. |
| 239 |
0x1000 packet contents. |
| 240 |
0x2000 hardware status. |
| 241 |
0x4000 Wake-on-LAN status. |
| 242 |
====== ============================= |
| 243 |
|
| 244 |
By default, the level of debugging messages is set 0x0001(general driver status). |
| 245 |
|
| 246 |
Check message level |
| 247 |
|
| 248 |
:: |
| 249 |
|
| 250 |
ethtool <ethX> | grep "Current message level" |
| 251 |
|
| 252 |
If you want to disable the output of messages:: |
| 253 |
|
| 254 |
ethtool -s <ethX> msglvl 0 |
| 255 |
|
| 256 |
RX flow rules (ntuple filters) |
| 257 |
------------------------------ |
| 258 |
|
| 259 |
There are separate rules supported, that applies in that order: |
| 260 |
|
| 261 |
1. 16 VLAN ID rules |
| 262 |
2. 16 L2 EtherType rules |
| 263 |
3. 8 L3/L4 5-Tuple rules |
| 264 |
|
| 265 |
|
| 266 |
The driver utilizes the ethtool interface for configuring ntuple filters, |
| 267 |
via ``ethtool -N <device> <filter>``. |
| 268 |
|
| 269 |
To enable or disable the RX flow rules:: |
| 270 |
|
| 271 |
ethtool -K ethX ntuple <on|off> |
| 272 |
|
| 273 |
When disabling ntuple filters, all the user programmed filters are |
| 274 |
flushed from the driver cache and hardware. All needed filters must |
| 275 |
be re-added when ntuple is re-enabled. |
| 276 |
|
| 277 |
Because of the fixed order of the rules, the location of filters is also fixed: |
| 278 |
|
| 279 |
- Locations 0 - 15 for VLAN ID filters |
| 280 |
- Locations 16 - 31 for L2 EtherType filters |
| 281 |
- Locations 32 - 39 for L3/L4 5-tuple filters (locations 32, 36 for IPv6) |
| 282 |
|
| 283 |
The L3/L4 5-tuple (protocol, source and destination IP address, source and |
| 284 |
destination TCP/UDP/SCTP port) is compared against 8 filters. For IPv4, up to |
| 285 |
8 source and destination addresses can be matched. For IPv6, up to 2 pairs of |
| 286 |
addresses can be supported. Source and destination ports are only compared for |
| 287 |
TCP/UDP/SCTP packets. |
| 288 |
|
| 289 |
To add a filter that directs packet to queue 5, use |
| 290 |
``<-N|-U|--config-nfc|--config-ntuple>`` switch:: |
| 291 |
|
| 292 |
ethtool -N <ethX> flow-type udp4 src-ip 10.0.0.1 dst-ip 10.0.0.2 src-port 2000 dst-port 2001 action 5 <loc 32> |
| 293 |
|
| 294 |
- action is the queue number. |
| 295 |
- loc is the rule number. |
| 296 |
|
| 297 |
For ``flow-type ip4|udp4|tcp4|sctp4|ip6|udp6|tcp6|sctp6`` you must set the loc |
| 298 |
number within 32 - 39. |
| 299 |
For ``flow-type ip4|udp4|tcp4|sctp4|ip6|udp6|tcp6|sctp6`` you can set 8 rules |
| 300 |
for traffic IPv4 or you can set 2 rules for traffic IPv6. Loc number traffic |
| 301 |
IPv6 is 32 and 36. |
| 302 |
At the moment you can not use IPv4 and IPv6 filters at the same time. |
| 303 |
|
| 304 |
Example filter for IPv6 filter traffic:: |
| 305 |
|
| 306 |
sudo ethtool -N <ethX> flow-type tcp6 src-ip 2001:db8:0:f101::1 dst-ip 2001:db8:0:f101::2 action 1 loc 32 |
| 307 |
sudo ethtool -N <ethX> flow-type ip6 src-ip 2001:db8:0:f101::2 dst-ip 2001:db8:0:f101::5 action -1 loc 36 |
| 308 |
|
| 309 |
Example filter for IPv4 filter traffic:: |
| 310 |
|
| 311 |
sudo ethtool -N <ethX> flow-type udp4 src-ip 10.0.0.4 dst-ip 10.0.0.7 src-port 2000 dst-port 2001 loc 32 |
| 312 |
sudo ethtool -N <ethX> flow-type tcp4 src-ip 10.0.0.3 dst-ip 10.0.0.9 src-port 2000 dst-port 2001 loc 33 |
| 313 |
sudo ethtool -N <ethX> flow-type ip4 src-ip 10.0.0.6 dst-ip 10.0.0.4 loc 34 |
| 314 |
|
| 315 |
If you set action -1, then all traffic corresponding to the filter will be discarded. |
| 316 |
|
| 317 |
The maximum value action is 31. |
| 318 |
|
| 319 |
|
| 320 |
The VLAN filter (VLAN id) is compared against 16 filters. |
| 321 |
VLAN id must be accompanied by mask 0xF000. That is to distinguish VLAN filter |
| 322 |
from L2 Ethertype filter with UserPriority since both User Priority and VLAN ID |
| 323 |
are passed in the same 'vlan' parameter. |
| 324 |
|
| 325 |
To add a filter that directs packets from VLAN 2001 to queue 5:: |
| 326 |
|
| 327 |
ethtool -N <ethX> flow-type ip4 vlan 2001 m 0xF000 action 1 loc 0 |
| 328 |
|
| 329 |
|
| 330 |
L2 EtherType filters allows filter packet by EtherType field or both EtherType |
| 331 |
and User Priority (PCP) field of 802.1Q. |
| 332 |
UserPriority (vlan) parameter must be accompanied by mask 0x1FFF. That is to |
| 333 |
distinguish VLAN filter from L2 Ethertype filter with UserPriority since both |
| 334 |
User Priority and VLAN ID are passed in the same 'vlan' parameter. |
| 335 |
|
| 336 |
To add a filter that directs IP4 packess of priority 3 to queue 3:: |
| 337 |
|
| 338 |
ethtool -N <ethX> flow-type ether proto 0x800 vlan 0x600 m 0x1FFF action 3 loc 16 |
| 339 |
|
| 340 |
To see the list of filters currently present:: |
| 341 |
|
| 342 |
ethtool <-u|-n|--show-nfc|--show-ntuple> <ethX> |
| 343 |
|
| 344 |
Rules may be deleted from the table itself. This is done using:: |
| 345 |
|
| 346 |
sudo ethtool <-N|-U|--config-nfc|--config-ntuple> <ethX> delete <loc> |
| 347 |
|
| 348 |
- loc is the rule number to be deleted. |
| 349 |
|
| 350 |
Rx filters is an interface to load the filter table that funnels all flow |
| 351 |
into queue 0 unless an alternative queue is specified using "action". In that |
| 352 |
case, any flow that matches the filter criteria will be directed to the |
| 353 |
appropriate queue. RX filters is supported on all kernels 2.6.30 and later. |
| 354 |
|
| 355 |
RSS for UDP |
| 356 |
----------- |
| 357 |
|
| 358 |
Currently, NIC does not support RSS for fragmented IP packets, which leads to |
| 359 |
incorrect working of RSS for fragmented UDP traffic. To disable RSS for UDP the |
| 360 |
RX Flow L3/L4 rule may be used. |
| 361 |
|
| 362 |
Example:: |
| 363 |
|
| 364 |
ethtool -N eth0 flow-type udp4 action 0 loc 32 |
| 365 |
|
| 366 |
UDP GSO hardware offload |
| 367 |
------------------------ |
| 368 |
|
| 369 |
UDP GSO allows to boost UDP tx rates by offloading UDP headers allocation |
| 370 |
into hardware. A special userspace socket option is required for this, |
| 371 |
could be validated with /kernel/tools/testing/selftests/net/:: |
| 372 |
|
| 373 |
udpgso_bench_tx -u -4 -D 10.0.1.1 -s 6300 -S 100 |
| 374 |
|
| 375 |
Will cause sending out of 100 byte sized UDP packets formed from single |
| 376 |
6300 bytes user buffer. |
| 377 |
|
| 378 |
UDP GSO is configured by:: |
| 379 |
|
| 380 |
ethtool -K eth0 tx-udp-segmentation on |
| 381 |
|
| 382 |
Private flags (testing) |
| 383 |
----------------------- |
| 384 |
|
| 385 |
Atlantic driver supports private flags for hardware custom features:: |
| 386 |
|
| 387 |
$ ethtool --show-priv-flags ethX |
| 388 |
|
| 389 |
Private flags for ethX: |
| 390 |
DMASystemLoopback : off |
| 391 |
PKTSystemLoopback : off |
| 392 |
DMANetworkLoopback : off |
| 393 |
PHYInternalLoopback: off |
| 394 |
PHYExternalLoopback: off |
| 395 |
|
| 396 |
Example:: |
| 397 |
|
| 398 |
$ ethtool --set-priv-flags ethX DMASystemLoopback on |
| 399 |
|
| 400 |
DMASystemLoopback: DMA Host loopback. |
| 401 |
PKTSystemLoopback: Packet buffer host loopback. |
| 402 |
DMANetworkLoopback: Network side loopback on DMA block. |
| 403 |
PHYInternalLoopback: Internal loopback on Phy. |
| 404 |
PHYExternalLoopback: External loopback on Phy (with loopback ethernet cable). |
| 405 |
|
| 406 |
|
| 407 |
Command Line Parameters |
| 408 |
======================= |
| 409 |
The following command line parameters are available on atlantic driver: |
| 410 |
|
| 411 |
aq_itr -Interrupt throttling mode |
| 412 |
--------------------------------- |
| 413 |
Accepted values: 0, 1, 0xFFFF |
| 414 |
|
| 415 |
Default value: 0xFFFF |
| 416 |
|
| 417 |
====== ============================================================== |
| 418 |
0 Disable interrupt throttling. |
| 419 |
1 Enable interrupt throttling and use specified tx and rx rates. |
| 420 |
0xFFFF Auto throttling mode. Driver will choose the best RX and TX |
| 421 |
interrupt throttling settings based on link speed. |
| 422 |
====== ============================================================== |
| 423 |
|
| 424 |
aq_itr_tx - TX interrupt throttle rate |
| 425 |
-------------------------------------- |
| 426 |
|
| 427 |
Accepted values: 0 - 0x1FF |
| 428 |
|
| 429 |
Default value: 0 |
| 430 |
|
| 431 |
TX side throttling in microseconds. Adapter will setup maximum interrupt delay |
| 432 |
to this value. Minimum interrupt delay will be a half of this value |
| 433 |
|
| 434 |
aq_itr_rx - RX interrupt throttle rate |
| 435 |
-------------------------------------- |
| 436 |
|
| 437 |
Accepted values: 0 - 0x1FF |
| 438 |
|
| 439 |
Default value: 0 |
| 440 |
|
| 441 |
RX side throttling in microseconds. Adapter will setup maximum interrupt delay |
| 442 |
to this value. Minimum interrupt delay will be a half of this value |
| 443 |
|
| 444 |
.. note:: |
| 445 |
|
| 446 |
ITR settings could be changed in runtime by ethtool -c means (see below) |
| 447 |
|
| 448 |
Config file parameters |
| 449 |
====================== |
| 450 |
|
| 451 |
For some fine tuning and performance optimizations, |
| 452 |
some parameters can be changed in the {source_dir}/aq_cfg.h file. |
| 453 |
|
| 454 |
AQ_CFG_RX_PAGEORDER |
| 455 |
------------------- |
| 456 |
|
| 457 |
Default value: 0 |
| 458 |
|
| 459 |
RX page order override. That's a power of 2 number of RX pages allocated for |
| 460 |
each descriptor. Received descriptor size is still limited by |
| 461 |
AQ_CFG_RX_FRAME_MAX. |
| 462 |
|
| 463 |
Increasing pageorder makes page reuse better (actual on iommu enabled systems). |
| 464 |
|
| 465 |
AQ_CFG_RX_REFILL_THRES |
| 466 |
---------------------- |
| 467 |
|
| 468 |
Default value: 32 |
| 469 |
|
| 470 |
RX refill threshold. RX path will not refill freed descriptors until the |
| 471 |
specified number of free descriptors is observed. Larger values may help |
| 472 |
better page reuse but may lead to packet drops as well. |
| 473 |
|
| 474 |
AQ_CFG_VECS_DEF |
| 475 |
--------------- |
| 476 |
|
| 477 |
Number of queues |
| 478 |
|
| 479 |
Valid Range: 0 - 8 (up to AQ_CFG_VECS_MAX) |
| 480 |
|
| 481 |
Default value: 8 |
| 482 |
|
| 483 |
Notice this value will be capped by the number of cores available on the system. |
| 484 |
|
| 485 |
AQ_CFG_IS_RSS_DEF |
| 486 |
----------------- |
| 487 |
|
| 488 |
Enable/disable Receive Side Scaling |
| 489 |
|
| 490 |
This feature allows the adapter to distribute receive processing |
| 491 |
across multiple CPU-cores and to prevent from overloading a single CPU core. |
| 492 |
|
| 493 |
Valid values |
| 494 |
|
| 495 |
== ======== |
| 496 |
0 disabled |
| 497 |
1 enabled |
| 498 |
== ======== |
| 499 |
|
| 500 |
Default value: 1 |
| 501 |
|
| 502 |
AQ_CFG_NUM_RSS_QUEUES_DEF |
| 503 |
------------------------- |
| 504 |
|
| 505 |
Number of queues for Receive Side Scaling |
| 506 |
|
| 507 |
Valid Range: 0 - 8 (up to AQ_CFG_VECS_DEF) |
| 508 |
|
| 509 |
Default value: AQ_CFG_VECS_DEF |
| 510 |
|
| 511 |
AQ_CFG_IS_LRO_DEF |
| 512 |
----------------- |
| 513 |
|
| 514 |
Enable/disable Large Receive Offload |
| 515 |
|
| 516 |
This offload enables the adapter to coalesce multiple TCP segments and indicate |
| 517 |
them as a single coalesced unit to the OS networking subsystem. |
| 518 |
|
| 519 |
The system consumes less energy but it also introduces more latency in packets |
| 520 |
processing. |
| 521 |
|
| 522 |
Valid values |
| 523 |
|
| 524 |
== ======== |
| 525 |
0 disabled |
| 526 |
1 enabled |
| 527 |
== ======== |
| 528 |
|
| 529 |
Default value: 1 |
| 530 |
|
| 531 |
AQ_CFG_TX_CLEAN_BUDGET |
| 532 |
---------------------- |
| 533 |
|
| 534 |
Maximum descriptors to cleanup on TX at once. |
| 535 |
|
| 536 |
Default value: 256 |
| 537 |
|
| 538 |
After the aq_cfg.h file changed the driver must be rebuilt to take effect. |
| 539 |
|
| 540 |
Support |
| 541 |
======= |
| 542 |
|
| 543 |
If an issue is identified with the released source code on the supported |
| 544 |
kernel with a supported adapter, email the specific information related |
| 545 |
to the issue to [email protected] |
| 546 |
|
| 547 |
License |
| 548 |
======= |
| 549 |
|
| 550 |
aQuantia Corporation Network Driver |
| 551 |
|
| 552 |
Copyright |copy| 2014 - 2019 aQuantia Corporation. |
| 553 |
|
| 554 |
This program is free software; you can redistribute it and/or modify it |
| 555 |
under the terms and conditions of the GNU General Public License, |
| 556 |
version 2, as published by the Free Software Foundation. |