| 1 |
this is a small utility program illustrating the use of the new (2020) |
| 2 |
TRAU related blocks like I.460 mux, TRAU frame synchronizer, TRAU frame |
| 3 |
decoder and trau2rtp conversion. |
| 4 |
|
| 5 |
The only argument to the progrmam is the input file, which can either be |
| 6 |
|
| 7 |
* a DAHDI device like /dev/dahdi/chan/004/002 to use TS2 on span/line 4 |
| 8 |
* a pre-recorded capture file containing raw binary 64k timeslot data |
| 9 |
|
| 10 |
The tool will automatically determine if a regular file or a DAHDI device |
| 11 |
was passed, and behave accordingly. |
| 12 |
|
| 13 |
|
| 14 |
== reading capture files |
| 15 |
|
| 16 |
There are FR and EFR exampel captures included. |
| 17 |
|
| 18 |
The input data (*.log.bz2) was generated using strace on an osmo-nitb process |
| 19 |
while a MO-to-MT call was running on two sub-slots of TS2. |
| 20 |
|
| 21 |
The strace log is converted to a binary stream of the raw 64bit E1 slot |
| 22 |
using strace-write-parse.py |
| 23 |
|
| 24 |
You can use the too like this: |
| 25 |
|
| 26 |
* start osmo-gapk as a RTP to ALSA sink like |
| 27 |
osmo-gapk -I 127.0.0.1/9999 -f gsm -g rawpcm-s16le -A default # for FR |
| 28 |
osmo-gapk -I 127.0.0.1/9999 -f rtp-efr -g rawpcm-s16le -A default # for EFR |
| 29 |
|
| 30 |
* run trau2rtp to read the bin file and generate RTP: |
| 31 |
./trau2rtp e1_ts2_fr.bin # for FR |
| 32 |
./trau2rtp e1_ts2_efr.bin # for EFR |
| 33 |
|
| 34 |
|
| 35 |
== Interfacing a DAHDI device |
| 36 |
|
| 37 |
It can be operated in two modes: |
| 38 |
|
| 39 |
a) local loop between sub-slots 1+2 (bit-offset 2 + 4), i.e. connecting the first |
| 40 |
two calls on a 'typical' TRX0 where the first sub-slot (bit-offset 0) is not |
| 41 |
used, |
| 42 |
|
| 43 |
OR |
| 44 |
|
| 45 |
b) interface between 64k TRAU slot and RTP. IP addresses + port numbers are |
| 46 |
compiled-in, you need to modify them accordingly. |
| 47 |
|
| 48 |
|
| 49 |
In mode "a", you can use it to have voice calls for low-level debugging without a media |
| 50 |
gateway. |
| 51 |
|
| 52 |
In mode "b", you can e.g. play back audio from an exterenal RTP source and listen to it |
| 53 |
over the GSM attached mobile phone. |
| 54 |
|
| 55 |
Command line for playing back EFR via RTP: |
| 56 |
./osmo-gapk -f amr-efr -i ../tests/ref-files/hhgttg_part1_5.s16.amr-efr -g rtp-efr -O 192.168.11.179/8002 -t -l |
| 57 |
|
| 58 |
Command line for playing back FR via RTP: |
| 59 |
./osmo-gapk -f gsm -i ../tests/ref-files/hhgttg_part1_5.s16.gsm -g gsm -O 192.168.11.179/8002 -t -l |
| 60 |
|
| 61 |
The '-l' option is experimental and requires gapk patch I2d552695dfb4cc96039838e79e0f5ae25a6737c8. If you want |
| 62 |
to use it with EFR, you need to change pq_file.c to skip the AMR file header when rewinding: |
| 63 |
|
| 64 |
- fseek(state->fh, 0, SEEK_SET); |
| 65 |
+ fseek(state->fh, 6, SEEK_SET); |
| 66 |
|
| 67 |
The code has been tested against BS-11 and RBS6000/DUG20 in both modes (loop vs. RTP) and for FR and EFR. |