| 1 |
/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */ |
| 2 |
/* |
| 3 |
* ethtool.h: Defines for Linux ethtool. |
| 4 |
* |
| 5 |
* Copyright (C) 1998 David S. Miller ([email protected]) |
| 6 |
* Copyright 2001 Jeff Garzik <[email protected]> |
| 7 |
* Portions Copyright 2001 Sun Microsystems ([email protected]) |
| 8 |
* Portions Copyright 2002 Intel ([email protected], |
| 9 |
* [email protected], |
| 10 |
* [email protected]) |
| 11 |
* Portions Copyright (C) Sun Microsystems 2008 |
| 12 |
*/ |
| 13 |
|
| 14 |
#ifndef _LINUX_ETHTOOL_H |
| 15 |
#define _LINUX_ETHTOOL_H |
| 16 |
|
| 17 |
#include <linux/const.h> |
| 18 |
#include <linux/types.h> |
| 19 |
#include <linux/if_ether.h> |
| 20 |
|
| 21 |
#include <limits.h> /* for INT_MAX */ |
| 22 |
|
| 23 |
/* All structures exposed to userland should be defined such that they |
| 24 |
* have the same layout for 32-bit and 64-bit userland. |
| 25 |
*/ |
| 26 |
|
| 27 |
/* Note on reserved space. |
| 28 |
* Reserved fields must not be accessed directly by user space because |
| 29 |
* they may be replaced by a different field in the future. They must |
| 30 |
* be initialized to zero before making the request, e.g. via memset |
| 31 |
* of the entire structure or implicitly by not being set in a structure |
| 32 |
* initializer. |
| 33 |
*/ |
| 34 |
|
| 35 |
/** |
| 36 |
* struct ethtool_cmd - DEPRECATED, link control and status |
| 37 |
* This structure is DEPRECATED, please use struct ethtool_link_settings. |
| 38 |
* @cmd: Command number = %ETHTOOL_GSET or %ETHTOOL_SSET |
| 39 |
* @supported: Bitmask of %SUPPORTED_* flags for the link modes, |
| 40 |
* physical connectors and other link features for which the |
| 41 |
* interface supports autonegotiation or auto-detection. |
| 42 |
* Read-only. |
| 43 |
* @advertising: Bitmask of %ADVERTISED_* flags for the link modes, |
| 44 |
* physical connectors and other link features that are |
| 45 |
* advertised through autonegotiation or enabled for |
| 46 |
* auto-detection. |
| 47 |
* @speed: Low bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN |
| 48 |
* @duplex: Duplex mode; one of %DUPLEX_* |
| 49 |
* @port: Physical connector type; one of %PORT_* |
| 50 |
* @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not |
| 51 |
* applicable. For clause 45 PHYs this is the PRTAD. |
| 52 |
* @transceiver: Historically used to distinguish different possible |
| 53 |
* PHY types, but not in a consistent way. Deprecated. |
| 54 |
* @autoneg: Enable/disable autonegotiation and auto-detection; |
| 55 |
* either %AUTONEG_DISABLE or %AUTONEG_ENABLE |
| 56 |
* @mdio_support: Bitmask of %ETH_MDIO_SUPPORTS_* flags for the MDIO |
| 57 |
* protocols supported by the interface; 0 if unknown. |
| 58 |
* Read-only. |
| 59 |
* @maxtxpkt: Historically used to report TX IRQ coalescing; now |
| 60 |
* obsoleted by &struct ethtool_coalesce. Read-only; deprecated. |
| 61 |
* @maxrxpkt: Historically used to report RX IRQ coalescing; now |
| 62 |
* obsoleted by &struct ethtool_coalesce. Read-only; deprecated. |
| 63 |
* @speed_hi: High bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN |
| 64 |
* @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of |
| 65 |
* %ETH_TP_MDI_*. If the status is unknown or not applicable, the |
| 66 |
* value will be %ETH_TP_MDI_INVALID. Read-only. |
| 67 |
* @eth_tp_mdix_ctrl: Ethernet twisted pair MDI(-X) control; one of |
| 68 |
* %ETH_TP_MDI_*. If MDI(-X) control is not implemented, reads |
| 69 |
* yield %ETH_TP_MDI_INVALID and writes may be ignored or rejected. |
| 70 |
* When written successfully, the link should be renegotiated if |
| 71 |
* necessary. |
| 72 |
* @lp_advertising: Bitmask of %ADVERTISED_* flags for the link modes |
| 73 |
* and other link features that the link partner advertised |
| 74 |
* through autonegotiation; 0 if unknown or not applicable. |
| 75 |
* Read-only. |
| 76 |
* @reserved: Reserved for future use; see the note on reserved space. |
| 77 |
* |
| 78 |
* The link speed in Mbps is split between @speed and @speed_hi. Use |
| 79 |
* the ethtool_cmd_speed() and ethtool_cmd_speed_set() functions to |
| 80 |
* access it. |
| 81 |
* |
| 82 |
* If autonegotiation is disabled, the speed and @duplex represent the |
| 83 |
* fixed link mode and are writable if the driver supports multiple |
| 84 |
* link modes. If it is enabled then they are read-only; if the link |
| 85 |
* is up they represent the negotiated link mode; if the link is down, |
| 86 |
* the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and |
| 87 |
* @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode. |
| 88 |
* |
| 89 |
* Some hardware interfaces may have multiple PHYs and/or physical |
| 90 |
* connectors fitted or do not allow the driver to detect which are |
| 91 |
* fitted. For these interfaces @port and/or @phy_address may be |
| 92 |
* writable, possibly dependent on @autoneg being %AUTONEG_DISABLE. |
| 93 |
* Otherwise, attempts to write different values may be ignored or |
| 94 |
* rejected. |
| 95 |
* |
| 96 |
* Users should assume that all fields not marked read-only are |
| 97 |
* writable and subject to validation by the driver. They should use |
| 98 |
* %ETHTOOL_GSET to get the current values before making specific |
| 99 |
* changes and then applying them with %ETHTOOL_SSET. |
| 100 |
* |
| 101 |
* Deprecated fields should be ignored by both users and drivers. |
| 102 |
*/ |
| 103 |
struct ethtool_cmd { |
| 104 |
__u32 cmd; |
| 105 |
__u32 supported; |
| 106 |
__u32 advertising; |
| 107 |
__u16 speed; |
| 108 |
__u8 duplex; |
| 109 |
__u8 port; |
| 110 |
__u8 phy_address; |
| 111 |
__u8 transceiver; |
| 112 |
__u8 autoneg; |
| 113 |
__u8 mdio_support; |
| 114 |
__u32 maxtxpkt; |
| 115 |
__u32 maxrxpkt; |
| 116 |
__u16 speed_hi; |
| 117 |
__u8 eth_tp_mdix; |
| 118 |
__u8 eth_tp_mdix_ctrl; |
| 119 |
__u32 lp_advertising; |
| 120 |
__u32 reserved[2]; |
| 121 |
}; |
| 122 |
|
| 123 |
static __inline__ void ethtool_cmd_speed_set(struct ethtool_cmd *ep, |
| 124 |
__u32 speed) |
| 125 |
{ |
| 126 |
ep->speed = (__u16)(speed & 0xFFFF); |
| 127 |
ep->speed_hi = (__u16)(speed >> 16); |
| 128 |
} |
| 129 |
|
| 130 |
static __inline__ __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep) |
| 131 |
{ |
| 132 |
return (ep->speed_hi << 16) | ep->speed; |
| 133 |
} |
| 134 |
|
| 135 |
/* Device supports clause 22 register access to PHY or peripherals |
| 136 |
* using the interface defined in <linux/mii.h>. This should not be |
| 137 |
* set if there are known to be no such peripherals present or if |
| 138 |
* the driver only emulates clause 22 registers for compatibility. |
| 139 |
*/ |
| 140 |
#define ETH_MDIO_SUPPORTS_C22 1 |
| 141 |
|
| 142 |
/* Device supports clause 45 register access to PHY or peripherals |
| 143 |
* using the interface defined in <linux/mii.h> and <linux/mdio.h>. |
| 144 |
* This should not be set if there are known to be no such peripherals |
| 145 |
* present. |
| 146 |
*/ |
| 147 |
#define ETH_MDIO_SUPPORTS_C45 2 |
| 148 |
|
| 149 |
#define ETHTOOL_FWVERS_LEN 32 |
| 150 |
#define ETHTOOL_BUSINFO_LEN 32 |
| 151 |
#define ETHTOOL_EROMVERS_LEN 32 |
| 152 |
|
| 153 |
/** |
| 154 |
* struct ethtool_drvinfo - general driver and device information |
| 155 |
* @cmd: Command number = %ETHTOOL_GDRVINFO |
| 156 |
* @driver: Driver short name. This should normally match the name |
| 157 |
* in its bus driver structure (e.g. pci_driver::name). Must |
| 158 |
* not be an empty string. |
| 159 |
* @version: Driver version string; may be an empty string |
| 160 |
* @fw_version: Firmware version string; driver defined; may be an |
| 161 |
* empty string |
| 162 |
* @erom_version: Expansion ROM version string; driver defined; may be |
| 163 |
* an empty string |
| 164 |
* @bus_info: Device bus address. This should match the dev_name() |
| 165 |
* string for the underlying bus device, if there is one. May be |
| 166 |
* an empty string. |
| 167 |
* @reserved2: Reserved for future use; see the note on reserved space. |
| 168 |
* @n_priv_flags: Number of flags valid for %ETHTOOL_GPFLAGS and |
| 169 |
* %ETHTOOL_SPFLAGS commands; also the number of strings in the |
| 170 |
* %ETH_SS_PRIV_FLAGS set |
| 171 |
* @n_stats: Number of u64 statistics returned by the %ETHTOOL_GSTATS |
| 172 |
* command; also the number of strings in the %ETH_SS_STATS set |
| 173 |
* @testinfo_len: Number of results returned by the %ETHTOOL_TEST |
| 174 |
* command; also the number of strings in the %ETH_SS_TEST set |
| 175 |
* @eedump_len: Size of EEPROM accessible through the %ETHTOOL_GEEPROM |
| 176 |
* and %ETHTOOL_SEEPROM commands, in bytes |
| 177 |
* @regdump_len: Size of register dump returned by the %ETHTOOL_GREGS |
| 178 |
* command, in bytes |
| 179 |
* |
| 180 |
* Users can use the %ETHTOOL_GSSET_INFO command to get the number of |
| 181 |
* strings in any string set (from Linux 2.6.34). |
| 182 |
*/ |
| 183 |
struct ethtool_drvinfo { |
| 184 |
__u32 cmd; |
| 185 |
char driver[32]; |
| 186 |
char version[32]; |
| 187 |
char fw_version[ETHTOOL_FWVERS_LEN]; |
| 188 |
char bus_info[ETHTOOL_BUSINFO_LEN]; |
| 189 |
char erom_version[ETHTOOL_EROMVERS_LEN]; |
| 190 |
char reserved2[12]; |
| 191 |
__u32 n_priv_flags; |
| 192 |
__u32 n_stats; |
| 193 |
__u32 testinfo_len; |
| 194 |
__u32 eedump_len; |
| 195 |
__u32 regdump_len; |
| 196 |
}; |
| 197 |
|
| 198 |
#define SOPASS_MAX 6 |
| 199 |
|
| 200 |
/** |
| 201 |
* struct ethtool_wolinfo - Wake-On-Lan configuration |
| 202 |
* @cmd: Command number = %ETHTOOL_GWOL or %ETHTOOL_SWOL |
| 203 |
* @supported: Bitmask of %WAKE_* flags for supported Wake-On-Lan modes. |
| 204 |
* Read-only. |
| 205 |
* @wolopts: Bitmask of %WAKE_* flags for enabled Wake-On-Lan modes. |
| 206 |
* @sopass: SecureOn(tm) password; meaningful only if %WAKE_MAGICSECURE |
| 207 |
* is set in @wolopts. |
| 208 |
*/ |
| 209 |
struct ethtool_wolinfo { |
| 210 |
__u32 cmd; |
| 211 |
__u32 supported; |
| 212 |
__u32 wolopts; |
| 213 |
__u8 sopass[SOPASS_MAX]; |
| 214 |
}; |
| 215 |
|
| 216 |
/* for passing single values */ |
| 217 |
struct ethtool_value { |
| 218 |
__u32 cmd; |
| 219 |
__u32 data; |
| 220 |
}; |
| 221 |
|
| 222 |
#define PFC_STORM_PREVENTION_AUTO 0xffff |
| 223 |
#define PFC_STORM_PREVENTION_DISABLE 0 |
| 224 |
|
| 225 |
enum tunable_id { |
| 226 |
ETHTOOL_ID_UNSPEC, |
| 227 |
ETHTOOL_RX_COPYBREAK, |
| 228 |
ETHTOOL_TX_COPYBREAK, |
| 229 |
ETHTOOL_PFC_PREVENTION_TOUT, /* timeout in msecs */ |
| 230 |
ETHTOOL_TX_COPYBREAK_BUF_SIZE, |
| 231 |
/* |
| 232 |
* Add your fresh new tunable attribute above and remember to update |
| 233 |
* tunable_strings[] in net/ethtool/common.c |
| 234 |
*/ |
| 235 |
__ETHTOOL_TUNABLE_COUNT, |
| 236 |
}; |
| 237 |
|
| 238 |
enum tunable_type_id { |
| 239 |
ETHTOOL_TUNABLE_UNSPEC, |
| 240 |
ETHTOOL_TUNABLE_U8, |
| 241 |
ETHTOOL_TUNABLE_U16, |
| 242 |
ETHTOOL_TUNABLE_U32, |
| 243 |
ETHTOOL_TUNABLE_U64, |
| 244 |
ETHTOOL_TUNABLE_STRING, |
| 245 |
ETHTOOL_TUNABLE_S8, |
| 246 |
ETHTOOL_TUNABLE_S16, |
| 247 |
ETHTOOL_TUNABLE_S32, |
| 248 |
ETHTOOL_TUNABLE_S64, |
| 249 |
}; |
| 250 |
|
| 251 |
struct ethtool_tunable { |
| 252 |
__u32 cmd; |
| 253 |
__u32 id; |
| 254 |
__u32 type_id; |
| 255 |
__u32 len; |
| 256 |
void *data[]; |
| 257 |
}; |
| 258 |
|
| 259 |
#define DOWNSHIFT_DEV_DEFAULT_COUNT 0xff |
| 260 |
#define DOWNSHIFT_DEV_DISABLE 0 |
| 261 |
|
| 262 |
/* Time in msecs after which link is reported as down |
| 263 |
* 0 = lowest time supported by the PHY |
| 264 |
* 0xff = off, link down detection according to standard |
| 265 |
*/ |
| 266 |
#define ETHTOOL_PHY_FAST_LINK_DOWN_ON 0 |
| 267 |
#define ETHTOOL_PHY_FAST_LINK_DOWN_OFF 0xff |
| 268 |
|
| 269 |
/* Energy Detect Power Down (EDPD) is a feature supported by some PHYs, where |
| 270 |
* the PHY's RX & TX blocks are put into a low-power mode when there is no |
| 271 |
* link detected (typically cable is un-plugged). For RX, only a minimal |
| 272 |
* link-detection is available, and for TX the PHY wakes up to send link pulses |
| 273 |
* to avoid any lock-ups in case the peer PHY may also be running in EDPD mode. |
| 274 |
* |
| 275 |
* Some PHYs may support configuration of the wake-up interval for TX pulses, |
| 276 |
* and some PHYs may support only disabling TX pulses entirely. For the latter |
| 277 |
* a special value is required (ETHTOOL_PHY_EDPD_NO_TX) so that this can be |
| 278 |
* configured from userspace (should the user want it). |
| 279 |
* |
| 280 |
* The interval units for TX wake-up are in milliseconds, since this should |
| 281 |
* cover a reasonable range of intervals: |
| 282 |
* - from 1 millisecond, which does not sound like much of a power-saver |
| 283 |
* - to ~65 seconds which is quite a lot to wait for a link to come up when |
| 284 |
* plugging a cable |
| 285 |
*/ |
| 286 |
#define ETHTOOL_PHY_EDPD_DFLT_TX_MSECS 0xffff |
| 287 |
#define ETHTOOL_PHY_EDPD_NO_TX 0xfffe |
| 288 |
#define ETHTOOL_PHY_EDPD_DISABLE 0 |
| 289 |
|
| 290 |
enum phy_tunable_id { |
| 291 |
ETHTOOL_PHY_ID_UNSPEC, |
| 292 |
ETHTOOL_PHY_DOWNSHIFT, |
| 293 |
ETHTOOL_PHY_FAST_LINK_DOWN, |
| 294 |
ETHTOOL_PHY_EDPD, |
| 295 |
/* |
| 296 |
* Add your fresh new phy tunable attribute above and remember to update |
| 297 |
* phy_tunable_strings[] in net/ethtool/common.c |
| 298 |
*/ |
| 299 |
__ETHTOOL_PHY_TUNABLE_COUNT, |
| 300 |
}; |
| 301 |
|
| 302 |
/** |
| 303 |
* struct ethtool_regs - hardware register dump |
| 304 |
* @cmd: Command number = %ETHTOOL_GREGS |
| 305 |
* @version: Dump format version. This is driver-specific and may |
| 306 |
* distinguish different chips/revisions. Drivers must use new |
| 307 |
* version numbers whenever the dump format changes in an |
| 308 |
* incompatible way. |
| 309 |
* @len: On entry, the real length of @data. On return, the number of |
| 310 |
* bytes used. |
| 311 |
* @data: Buffer for the register dump |
| 312 |
* |
| 313 |
* Users should use %ETHTOOL_GDRVINFO to find the maximum length of |
| 314 |
* a register dump for the interface. They must allocate the buffer |
| 315 |
* immediately following this structure. |
| 316 |
*/ |
| 317 |
struct ethtool_regs { |
| 318 |
__u32 cmd; |
| 319 |
__u32 version; |
| 320 |
__u32 len; |
| 321 |
__u8 data[]; |
| 322 |
}; |
| 323 |
|
| 324 |
/** |
| 325 |
* struct ethtool_eeprom - EEPROM dump |
| 326 |
* @cmd: Command number = %ETHTOOL_GEEPROM, %ETHTOOL_GMODULEEEPROM or |
| 327 |
* %ETHTOOL_SEEPROM |
| 328 |
* @magic: A 'magic cookie' value to guard against accidental changes. |
| 329 |
* The value passed in to %ETHTOOL_SEEPROM must match the value |
| 330 |
* returned by %ETHTOOL_GEEPROM for the same device. This is |
| 331 |
* unused when @cmd is %ETHTOOL_GMODULEEEPROM. |
| 332 |
* @offset: Offset within the EEPROM to begin reading/writing, in bytes |
| 333 |
* @len: On entry, number of bytes to read/write. On successful |
| 334 |
* return, number of bytes actually read/written. In case of |
| 335 |
* error, this may indicate at what point the error occurred. |
| 336 |
* @data: Buffer to read/write from |
| 337 |
* |
| 338 |
* Users may use %ETHTOOL_GDRVINFO or %ETHTOOL_GMODULEINFO to find |
| 339 |
* the length of an on-board or module EEPROM, respectively. They |
| 340 |
* must allocate the buffer immediately following this structure. |
| 341 |
*/ |
| 342 |
struct ethtool_eeprom { |
| 343 |
__u32 cmd; |
| 344 |
__u32 magic; |
| 345 |
__u32 offset; |
| 346 |
__u32 len; |
| 347 |
__u8 data[]; |
| 348 |
}; |
| 349 |
|
| 350 |
/** |
| 351 |
* struct ethtool_eee - Energy Efficient Ethernet information |
| 352 |
* @cmd: ETHTOOL_{G,S}EEE |
| 353 |
* @supported: Mask of %SUPPORTED_* flags for the speed/duplex combinations |
| 354 |
* for which there is EEE support. |
| 355 |
* @advertised: Mask of %ADVERTISED_* flags for the speed/duplex combinations |
| 356 |
* advertised as eee capable. |
| 357 |
* @lp_advertised: Mask of %ADVERTISED_* flags for the speed/duplex |
| 358 |
* combinations advertised by the link partner as eee capable. |
| 359 |
* @eee_active: Result of the eee auto negotiation. |
| 360 |
* @eee_enabled: EEE configured mode (enabled/disabled). |
| 361 |
* @tx_lpi_enabled: Whether the interface should assert its tx lpi, given |
| 362 |
* that eee was negotiated. |
| 363 |
* @tx_lpi_timer: Time in microseconds the interface delays prior to asserting |
| 364 |
* its tx lpi (after reaching 'idle' state). Effective only when eee |
| 365 |
* was negotiated and tx_lpi_enabled was set. |
| 366 |
* @reserved: Reserved for future use; see the note on reserved space. |
| 367 |
*/ |
| 368 |
struct ethtool_eee { |
| 369 |
__u32 cmd; |
| 370 |
__u32 supported; |
| 371 |
__u32 advertised; |
| 372 |
__u32 lp_advertised; |
| 373 |
__u32 eee_active; |
| 374 |
__u32 eee_enabled; |
| 375 |
__u32 tx_lpi_enabled; |
| 376 |
__u32 tx_lpi_timer; |
| 377 |
__u32 reserved[2]; |
| 378 |
}; |
| 379 |
|
| 380 |
/** |
| 381 |
* struct ethtool_modinfo - plugin module eeprom information |
| 382 |
* @cmd: %ETHTOOL_GMODULEINFO |
| 383 |
* @type: Standard the module information conforms to %ETH_MODULE_SFF_xxxx |
| 384 |
* @eeprom_len: Length of the eeprom |
| 385 |
* @reserved: Reserved for future use; see the note on reserved space. |
| 386 |
* |
| 387 |
* This structure is used to return the information to |
| 388 |
* properly size memory for a subsequent call to %ETHTOOL_GMODULEEEPROM. |
| 389 |
* The type code indicates the eeprom data format |
| 390 |
*/ |
| 391 |
struct ethtool_modinfo { |
| 392 |
__u32 cmd; |
| 393 |
__u32 type; |
| 394 |
__u32 eeprom_len; |
| 395 |
__u32 reserved[8]; |
| 396 |
}; |
| 397 |
|
| 398 |
/** |
| 399 |
* struct ethtool_coalesce - coalescing parameters for IRQs and stats updates |
| 400 |
* @cmd: ETHTOOL_{G,S}COALESCE |
| 401 |
* @rx_coalesce_usecs: How many usecs to delay an RX interrupt after |
| 402 |
* a packet arrives. |
| 403 |
* @rx_max_coalesced_frames: Maximum number of packets to receive |
| 404 |
* before an RX interrupt. |
| 405 |
* @rx_coalesce_usecs_irq: Same as @rx_coalesce_usecs, except that |
| 406 |
* this value applies while an IRQ is being serviced by the host. |
| 407 |
* @rx_max_coalesced_frames_irq: Same as @rx_max_coalesced_frames, |
| 408 |
* except that this value applies while an IRQ is being serviced |
| 409 |
* by the host. |
| 410 |
* @tx_coalesce_usecs: How many usecs to delay a TX interrupt after |
| 411 |
* a packet is sent. |
| 412 |
* @tx_max_coalesced_frames: Maximum number of packets to be sent |
| 413 |
* before a TX interrupt. |
| 414 |
* @tx_coalesce_usecs_irq: Same as @tx_coalesce_usecs, except that |
| 415 |
* this value applies while an IRQ is being serviced by the host. |
| 416 |
* @tx_max_coalesced_frames_irq: Same as @tx_max_coalesced_frames, |
| 417 |
* except that this value applies while an IRQ is being serviced |
| 418 |
* by the host. |
| 419 |
* @stats_block_coalesce_usecs: How many usecs to delay in-memory |
| 420 |
* statistics block updates. Some drivers do not have an |
| 421 |
* in-memory statistic block, and in such cases this value is |
| 422 |
* ignored. This value must not be zero. |
| 423 |
* @use_adaptive_rx_coalesce: Enable adaptive RX coalescing. |
| 424 |
* @use_adaptive_tx_coalesce: Enable adaptive TX coalescing. |
| 425 |
* @pkt_rate_low: Threshold for low packet rate (packets per second). |
| 426 |
* @rx_coalesce_usecs_low: How many usecs to delay an RX interrupt after |
| 427 |
* a packet arrives, when the packet rate is below @pkt_rate_low. |
| 428 |
* @rx_max_coalesced_frames_low: Maximum number of packets to be received |
| 429 |
* before an RX interrupt, when the packet rate is below @pkt_rate_low. |
| 430 |
* @tx_coalesce_usecs_low: How many usecs to delay a TX interrupt after |
| 431 |
* a packet is sent, when the packet rate is below @pkt_rate_low. |
| 432 |
* @tx_max_coalesced_frames_low: Maximum nuumber of packets to be sent before |
| 433 |
* a TX interrupt, when the packet rate is below @pkt_rate_low. |
| 434 |
* @pkt_rate_high: Threshold for high packet rate (packets per second). |
| 435 |
* @rx_coalesce_usecs_high: How many usecs to delay an RX interrupt after |
| 436 |
* a packet arrives, when the packet rate is above @pkt_rate_high. |
| 437 |
* @rx_max_coalesced_frames_high: Maximum number of packets to be received |
| 438 |
* before an RX interrupt, when the packet rate is above @pkt_rate_high. |
| 439 |
* @tx_coalesce_usecs_high: How many usecs to delay a TX interrupt after |
| 440 |
* a packet is sent, when the packet rate is above @pkt_rate_high. |
| 441 |
* @tx_max_coalesced_frames_high: Maximum number of packets to be sent before |
| 442 |
* a TX interrupt, when the packet rate is above @pkt_rate_high. |
| 443 |
* @rate_sample_interval: How often to do adaptive coalescing packet rate |
| 444 |
* sampling, measured in seconds. Must not be zero. |
| 445 |
* |
| 446 |
* Each pair of (usecs, max_frames) fields specifies that interrupts |
| 447 |
* should be coalesced until |
| 448 |
* (usecs > 0 && time_since_first_completion >= usecs) || |
| 449 |
* (max_frames > 0 && completed_frames >= max_frames) |
| 450 |
* |
| 451 |
* It is illegal to set both usecs and max_frames to zero as this |
| 452 |
* would cause interrupts to never be generated. To disable |
| 453 |
* coalescing, set usecs = 0 and max_frames = 1. |
| 454 |
* |
| 455 |
* Some implementations ignore the value of max_frames and use the |
| 456 |
* condition time_since_first_completion >= usecs |
| 457 |
* |
| 458 |
* This is deprecated. Drivers for hardware that does not support |
| 459 |
* counting completions should validate that max_frames == !rx_usecs. |
| 460 |
* |
| 461 |
* Adaptive RX/TX coalescing is an algorithm implemented by some |
| 462 |
* drivers to improve latency under low packet rates and improve |
| 463 |
* throughput under high packet rates. Some drivers only implement |
| 464 |
* one of RX or TX adaptive coalescing. Anything not implemented by |
| 465 |
* the driver causes these values to be silently ignored. |
| 466 |
* |
| 467 |
* When the packet rate is below @pkt_rate_high but above |
| 468 |
* @pkt_rate_low (both measured in packets per second) the |
| 469 |
* normal {rx,tx}_* coalescing parameters are used. |
| 470 |
*/ |
| 471 |
struct ethtool_coalesce { |
| 472 |
__u32 cmd; |
| 473 |
__u32 rx_coalesce_usecs; |
| 474 |
__u32 rx_max_coalesced_frames; |
| 475 |
__u32 rx_coalesce_usecs_irq; |
| 476 |
__u32 rx_max_coalesced_frames_irq; |
| 477 |
__u32 tx_coalesce_usecs; |
| 478 |
__u32 tx_max_coalesced_frames; |
| 479 |
__u32 tx_coalesce_usecs_irq; |
| 480 |
__u32 tx_max_coalesced_frames_irq; |
| 481 |
__u32 stats_block_coalesce_usecs; |
| 482 |
__u32 use_adaptive_rx_coalesce; |
| 483 |
__u32 use_adaptive_tx_coalesce; |
| 484 |
__u32 pkt_rate_low; |
| 485 |
__u32 rx_coalesce_usecs_low; |
| 486 |
__u32 rx_max_coalesced_frames_low; |
| 487 |
__u32 tx_coalesce_usecs_low; |
| 488 |
__u32 tx_max_coalesced_frames_low; |
| 489 |
__u32 pkt_rate_high; |
| 490 |
__u32 rx_coalesce_usecs_high; |
| 491 |
__u32 rx_max_coalesced_frames_high; |
| 492 |
__u32 tx_coalesce_usecs_high; |
| 493 |
__u32 tx_max_coalesced_frames_high; |
| 494 |
__u32 rate_sample_interval; |
| 495 |
}; |
| 496 |
|
| 497 |
/** |
| 498 |
* struct ethtool_ringparam - RX/TX ring parameters |
| 499 |
* @cmd: Command number = %ETHTOOL_GRINGPARAM or %ETHTOOL_SRINGPARAM |
| 500 |
* @rx_max_pending: Maximum supported number of pending entries per |
| 501 |
* RX ring. Read-only. |
| 502 |
* @rx_mini_max_pending: Maximum supported number of pending entries |
| 503 |
* per RX mini ring. Read-only. |
| 504 |
* @rx_jumbo_max_pending: Maximum supported number of pending entries |
| 505 |
* per RX jumbo ring. Read-only. |
| 506 |
* @tx_max_pending: Maximum supported number of pending entries per |
| 507 |
* TX ring. Read-only. |
| 508 |
* @rx_pending: Current maximum number of pending entries per RX ring |
| 509 |
* @rx_mini_pending: Current maximum number of pending entries per RX |
| 510 |
* mini ring |
| 511 |
* @rx_jumbo_pending: Current maximum number of pending entries per RX |
| 512 |
* jumbo ring |
| 513 |
* @tx_pending: Current maximum supported number of pending entries |
| 514 |
* per TX ring |
| 515 |
* |
| 516 |
* If the interface does not have separate RX mini and/or jumbo rings, |
| 517 |
* @rx_mini_max_pending and/or @rx_jumbo_max_pending will be 0. |
| 518 |
* |
| 519 |
* There may also be driver-dependent minimum values for the number |
| 520 |
* of entries per ring. |
| 521 |
*/ |
| 522 |
struct ethtool_ringparam { |
| 523 |
__u32 cmd; |
| 524 |
__u32 rx_max_pending; |
| 525 |
__u32 rx_mini_max_pending; |
| 526 |
__u32 rx_jumbo_max_pending; |
| 527 |
__u32 tx_max_pending; |
| 528 |
__u32 rx_pending; |
| 529 |
__u32 rx_mini_pending; |
| 530 |
__u32 rx_jumbo_pending; |
| 531 |
__u32 tx_pending; |
| 532 |
}; |
| 533 |
|
| 534 |
/** |
| 535 |
* struct ethtool_channels - configuring number of network channel |
| 536 |
* @cmd: ETHTOOL_{G,S}CHANNELS |
| 537 |
* @max_rx: Read only. Maximum number of receive channel the driver support. |
| 538 |
* @max_tx: Read only. Maximum number of transmit channel the driver support. |
| 539 |
* @max_other: Read only. Maximum number of other channel the driver support. |
| 540 |
* @max_combined: Read only. Maximum number of combined channel the driver |
| 541 |
* support. Set of queues RX, TX or other. |
| 542 |
* @rx_count: Valid values are in the range 1 to the max_rx. |
| 543 |
* @tx_count: Valid values are in the range 1 to the max_tx. |
| 544 |
* @other_count: Valid values are in the range 1 to the max_other. |
| 545 |
* @combined_count: Valid values are in the range 1 to the max_combined. |
| 546 |
* |
| 547 |
* This can be used to configure RX, TX and other channels. |
| 548 |
*/ |
| 549 |
|
| 550 |
struct ethtool_channels { |
| 551 |
__u32 cmd; |
| 552 |
__u32 max_rx; |
| 553 |
__u32 max_tx; |
| 554 |
__u32 max_other; |
| 555 |
__u32 max_combined; |
| 556 |
__u32 rx_count; |
| 557 |
__u32 tx_count; |
| 558 |
__u32 other_count; |
| 559 |
__u32 combined_count; |
| 560 |
}; |
| 561 |
|
| 562 |
/** |
| 563 |
* struct ethtool_pauseparam - Ethernet pause (flow control) parameters |
| 564 |
* @cmd: Command number = %ETHTOOL_GPAUSEPARAM or %ETHTOOL_SPAUSEPARAM |
| 565 |
* @autoneg: Flag to enable autonegotiation of pause frame use |
| 566 |
* @rx_pause: Flag to enable reception of pause frames |
| 567 |
* @tx_pause: Flag to enable transmission of pause frames |
| 568 |
* |
| 569 |
* Drivers should reject a non-zero setting of @autoneg when |
| 570 |
* autoneogotiation is disabled (or not supported) for the link. |
| 571 |
* |
| 572 |
* If the link is autonegotiated, drivers should use |
| 573 |
* mii_advertise_flowctrl() or similar code to set the advertised |
| 574 |
* pause frame capabilities based on the @rx_pause and @tx_pause flags, |
| 575 |
* even if @autoneg is zero. They should also allow the advertised |
| 576 |
* pause frame capabilities to be controlled directly through the |
| 577 |
* advertising field of &struct ethtool_cmd. |
| 578 |
* |
| 579 |
* If @autoneg is non-zero, the MAC is configured to send and/or |
| 580 |
* receive pause frames according to the result of autonegotiation. |
| 581 |
* Otherwise, it is configured directly based on the @rx_pause and |
| 582 |
* @tx_pause flags. |
| 583 |
*/ |
| 584 |
struct ethtool_pauseparam { |
| 585 |
__u32 cmd; |
| 586 |
__u32 autoneg; |
| 587 |
__u32 rx_pause; |
| 588 |
__u32 tx_pause; |
| 589 |
}; |
| 590 |
|
| 591 |
/* Link extended state */ |
| 592 |
enum ethtool_link_ext_state { |
| 593 |
ETHTOOL_LINK_EXT_STATE_AUTONEG, |
| 594 |
ETHTOOL_LINK_EXT_STATE_LINK_TRAINING_FAILURE, |
| 595 |
ETHTOOL_LINK_EXT_STATE_LINK_LOGICAL_MISMATCH, |
| 596 |
ETHTOOL_LINK_EXT_STATE_BAD_SIGNAL_INTEGRITY, |
| 597 |
ETHTOOL_LINK_EXT_STATE_NO_CABLE, |
| 598 |
ETHTOOL_LINK_EXT_STATE_CABLE_ISSUE, |
| 599 |
ETHTOOL_LINK_EXT_STATE_EEPROM_ISSUE, |
| 600 |
ETHTOOL_LINK_EXT_STATE_CALIBRATION_FAILURE, |
| 601 |
ETHTOOL_LINK_EXT_STATE_POWER_BUDGET_EXCEEDED, |
| 602 |
ETHTOOL_LINK_EXT_STATE_OVERHEAT, |
| 603 |
ETHTOOL_LINK_EXT_STATE_MODULE, |
| 604 |
}; |
| 605 |
|
| 606 |
/* More information in addition to ETHTOOL_LINK_EXT_STATE_AUTONEG. */ |
| 607 |
enum ethtool_link_ext_substate_autoneg { |
| 608 |
ETHTOOL_LINK_EXT_SUBSTATE_AN_NO_PARTNER_DETECTED = 1, |
| 609 |
ETHTOOL_LINK_EXT_SUBSTATE_AN_ACK_NOT_RECEIVED, |
| 610 |
ETHTOOL_LINK_EXT_SUBSTATE_AN_NEXT_PAGE_EXCHANGE_FAILED, |
| 611 |
ETHTOOL_LINK_EXT_SUBSTATE_AN_NO_PARTNER_DETECTED_FORCE_MODE, |
| 612 |
ETHTOOL_LINK_EXT_SUBSTATE_AN_FEC_MISMATCH_DURING_OVERRIDE, |
| 613 |
ETHTOOL_LINK_EXT_SUBSTATE_AN_NO_HCD, |
| 614 |
}; |
| 615 |
|
| 616 |
/* More information in addition to ETHTOOL_LINK_EXT_STATE_LINK_TRAINING_FAILURE. |
| 617 |
*/ |
| 618 |
enum ethtool_link_ext_substate_link_training { |
| 619 |
ETHTOOL_LINK_EXT_SUBSTATE_LT_KR_FRAME_LOCK_NOT_ACQUIRED = 1, |
| 620 |
ETHTOOL_LINK_EXT_SUBSTATE_LT_KR_LINK_INHIBIT_TIMEOUT, |
| 621 |
ETHTOOL_LINK_EXT_SUBSTATE_LT_KR_LINK_PARTNER_DID_NOT_SET_RECEIVER_READY, |
| 622 |
ETHTOOL_LINK_EXT_SUBSTATE_LT_REMOTE_FAULT, |
| 623 |
}; |
| 624 |
|
| 625 |
/* More information in addition to ETHTOOL_LINK_EXT_STATE_LINK_LOGICAL_MISMATCH. |
| 626 |
*/ |
| 627 |
enum ethtool_link_ext_substate_link_logical_mismatch { |
| 628 |
ETHTOOL_LINK_EXT_SUBSTATE_LLM_PCS_DID_NOT_ACQUIRE_BLOCK_LOCK = 1, |
| 629 |
ETHTOOL_LINK_EXT_SUBSTATE_LLM_PCS_DID_NOT_ACQUIRE_AM_LOCK, |
| 630 |
ETHTOOL_LINK_EXT_SUBSTATE_LLM_PCS_DID_NOT_GET_ALIGN_STATUS, |
| 631 |
ETHTOOL_LINK_EXT_SUBSTATE_LLM_FC_FEC_IS_NOT_LOCKED, |
| 632 |
ETHTOOL_LINK_EXT_SUBSTATE_LLM_RS_FEC_IS_NOT_LOCKED, |
| 633 |
}; |
| 634 |
|
| 635 |
/* More information in addition to ETHTOOL_LINK_EXT_STATE_BAD_SIGNAL_INTEGRITY. |
| 636 |
*/ |
| 637 |
enum ethtool_link_ext_substate_bad_signal_integrity { |
| 638 |
ETHTOOL_LINK_EXT_SUBSTATE_BSI_LARGE_NUMBER_OF_PHYSICAL_ERRORS = 1, |
| 639 |
ETHTOOL_LINK_EXT_SUBSTATE_BSI_UNSUPPORTED_RATE, |
| 640 |
ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_REFERENCE_CLOCK_LOST, |
| 641 |
ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_ALOS, |
| 642 |
}; |
| 643 |
|
| 644 |
/* More information in addition to ETHTOOL_LINK_EXT_STATE_CABLE_ISSUE. */ |
| 645 |
enum ethtool_link_ext_substate_cable_issue { |
| 646 |
ETHTOOL_LINK_EXT_SUBSTATE_CI_UNSUPPORTED_CABLE = 1, |
| 647 |
ETHTOOL_LINK_EXT_SUBSTATE_CI_CABLE_TEST_FAILURE, |
| 648 |
}; |
| 649 |
|
| 650 |
/* More information in addition to ETHTOOL_LINK_EXT_STATE_MODULE. */ |
| 651 |
enum ethtool_link_ext_substate_module { |
| 652 |
ETHTOOL_LINK_EXT_SUBSTATE_MODULE_CMIS_NOT_READY = 1, |
| 653 |
}; |
| 654 |
|
| 655 |
#define ETH_GSTRING_LEN 32 |
| 656 |
|
| 657 |
/** |
| 658 |
* enum ethtool_stringset - string set ID |
| 659 |
* @ETH_SS_TEST: Self-test result names, for use with %ETHTOOL_TEST |
| 660 |
* @ETH_SS_STATS: Statistic names, for use with %ETHTOOL_GSTATS |
| 661 |
* @ETH_SS_PRIV_FLAGS: Driver private flag names, for use with |
| 662 |
* %ETHTOOL_GPFLAGS and %ETHTOOL_SPFLAGS |
| 663 |
* @ETH_SS_NTUPLE_FILTERS: Previously used with %ETHTOOL_GRXNTUPLE; |
| 664 |
* now deprecated |
| 665 |
* @ETH_SS_FEATURES: Device feature names |
| 666 |
* @ETH_SS_RSS_HASH_FUNCS: RSS hush function names |
| 667 |
* @ETH_SS_TUNABLES: tunable names |
| 668 |
* @ETH_SS_PHY_STATS: Statistic names, for use with %ETHTOOL_GPHYSTATS |
| 669 |
* @ETH_SS_PHY_TUNABLES: PHY tunable names |
| 670 |
* @ETH_SS_LINK_MODES: link mode names |
| 671 |
* @ETH_SS_MSG_CLASSES: debug message class names |
| 672 |
* @ETH_SS_WOL_MODES: wake-on-lan modes |
| 673 |
* @ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags |
| 674 |
* @ETH_SS_TS_TX_TYPES: timestamping Tx types |
| 675 |
* @ETH_SS_TS_RX_FILTERS: timestamping Rx filters |
| 676 |
* @ETH_SS_UDP_TUNNEL_TYPES: UDP tunnel types |
| 677 |
* @ETH_SS_STATS_STD: standardized stats |
| 678 |
* @ETH_SS_STATS_ETH_PHY: names of IEEE 802.3 PHY statistics |
| 679 |
* @ETH_SS_STATS_ETH_MAC: names of IEEE 802.3 MAC statistics |
| 680 |
* @ETH_SS_STATS_ETH_CTRL: names of IEEE 802.3 MAC Control statistics |
| 681 |
* @ETH_SS_STATS_RMON: names of RMON statistics |
| 682 |
* |
| 683 |
* @ETH_SS_COUNT: number of defined string sets |
| 684 |
*/ |
| 685 |
enum ethtool_stringset { |
| 686 |
ETH_SS_TEST = 0, |
| 687 |
ETH_SS_STATS, |
| 688 |
ETH_SS_PRIV_FLAGS, |
| 689 |
ETH_SS_NTUPLE_FILTERS, |
| 690 |
ETH_SS_FEATURES, |
| 691 |
ETH_SS_RSS_HASH_FUNCS, |
| 692 |
ETH_SS_TUNABLES, |
| 693 |
ETH_SS_PHY_STATS, |
| 694 |
ETH_SS_PHY_TUNABLES, |
| 695 |
ETH_SS_LINK_MODES, |
| 696 |
ETH_SS_MSG_CLASSES, |
| 697 |
ETH_SS_WOL_MODES, |
| 698 |
ETH_SS_SOF_TIMESTAMPING, |
| 699 |
ETH_SS_TS_TX_TYPES, |
| 700 |
ETH_SS_TS_RX_FILTERS, |
| 701 |
ETH_SS_UDP_TUNNEL_TYPES, |
| 702 |
ETH_SS_STATS_STD, |
| 703 |
ETH_SS_STATS_ETH_PHY, |
| 704 |
ETH_SS_STATS_ETH_MAC, |
| 705 |
ETH_SS_STATS_ETH_CTRL, |
| 706 |
ETH_SS_STATS_RMON, |
| 707 |
|
| 708 |
/* add new constants above here */ |
| 709 |
ETH_SS_COUNT |
| 710 |
}; |
| 711 |
|
| 712 |
/** |
| 713 |
* enum ethtool_mac_stats_src - source of ethtool MAC statistics |
| 714 |
* @ETHTOOL_MAC_STATS_SRC_AGGREGATE: |
| 715 |
* if device supports a MAC merge layer, this retrieves the aggregate |
| 716 |
* statistics of the eMAC and pMAC. Otherwise, it retrieves just the |
| 717 |
* statistics of the single (express) MAC. |
| 718 |
* @ETHTOOL_MAC_STATS_SRC_EMAC: |
| 719 |
* if device supports a MM layer, this retrieves the eMAC statistics. |
| 720 |
* Otherwise, it retrieves the statistics of the single (express) MAC. |
| 721 |
* @ETHTOOL_MAC_STATS_SRC_PMAC: |
| 722 |
* if device supports a MM layer, this retrieves the pMAC statistics. |
| 723 |
*/ |
| 724 |
enum ethtool_mac_stats_src { |
| 725 |
ETHTOOL_MAC_STATS_SRC_AGGREGATE, |
| 726 |
ETHTOOL_MAC_STATS_SRC_EMAC, |
| 727 |
ETHTOOL_MAC_STATS_SRC_PMAC, |
| 728 |
}; |
| 729 |
|
| 730 |
/** |
| 731 |
* enum ethtool_module_power_mode_policy - plug-in module power mode policy |
| 732 |
* @ETHTOOL_MODULE_POWER_MODE_POLICY_HIGH: Module is always in high power mode. |
| 733 |
* @ETHTOOL_MODULE_POWER_MODE_POLICY_AUTO: Module is transitioned by the host |
| 734 |
* to high power mode when the first port using it is put administratively |
| 735 |
* up and to low power mode when the last port using it is put |
| 736 |
* administratively down. |
| 737 |
*/ |
| 738 |
enum ethtool_module_power_mode_policy { |
| 739 |
ETHTOOL_MODULE_POWER_MODE_POLICY_HIGH = 1, |
| 740 |
ETHTOOL_MODULE_POWER_MODE_POLICY_AUTO, |
| 741 |
}; |
| 742 |
|
| 743 |
/** |
| 744 |
* enum ethtool_module_power_mode - plug-in module power mode |
| 745 |
* @ETHTOOL_MODULE_POWER_MODE_LOW: Module is in low power mode. |
| 746 |
* @ETHTOOL_MODULE_POWER_MODE_HIGH: Module is in high power mode. |
| 747 |
*/ |
| 748 |
enum ethtool_module_power_mode { |
| 749 |
ETHTOOL_MODULE_POWER_MODE_LOW = 1, |
| 750 |
ETHTOOL_MODULE_POWER_MODE_HIGH, |
| 751 |
}; |
| 752 |
|
| 753 |
/** |
| 754 |
* enum ethtool_podl_pse_admin_state - operational state of the PoDL PSE |
| 755 |
* functions. IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState |
| 756 |
* @ETHTOOL_PODL_PSE_ADMIN_STATE_UNKNOWN: state of PoDL PSE functions are |
| 757 |
* unknown |
| 758 |
* @ETHTOOL_PODL_PSE_ADMIN_STATE_DISABLED: PoDL PSE functions are disabled |
| 759 |
* @ETHTOOL_PODL_PSE_ADMIN_STATE_ENABLED: PoDL PSE functions are enabled |
| 760 |
*/ |
| 761 |
enum ethtool_podl_pse_admin_state { |
| 762 |
ETHTOOL_PODL_PSE_ADMIN_STATE_UNKNOWN = 1, |
| 763 |
ETHTOOL_PODL_PSE_ADMIN_STATE_DISABLED, |
| 764 |
ETHTOOL_PODL_PSE_ADMIN_STATE_ENABLED, |
| 765 |
}; |
| 766 |
|
| 767 |
/** |
| 768 |
* enum ethtool_podl_pse_pw_d_status - power detection status of the PoDL PSE. |
| 769 |
* IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus: |
| 770 |
* @ETHTOOL_PODL_PSE_PW_D_STATUS_UNKNOWN: PoDL PSE |
| 771 |
* @ETHTOOL_PODL_PSE_PW_D_STATUS_DISABLED: "The enumeration “disabled” is |
| 772 |
* asserted true when the PoDL PSE state diagram variable mr_pse_enable is |
| 773 |
* false" |
| 774 |
* @ETHTOOL_PODL_PSE_PW_D_STATUS_SEARCHING: "The enumeration “searching” is |
| 775 |
* asserted true when either of the PSE state diagram variables |
| 776 |
* pi_detecting or pi_classifying is true." |
| 777 |
* @ETHTOOL_PODL_PSE_PW_D_STATUS_DELIVERING: "The enumeration “deliveringPower” |
| 778 |
* is asserted true when the PoDL PSE state diagram variable pi_powered is |
| 779 |
* true." |
| 780 |
* @ETHTOOL_PODL_PSE_PW_D_STATUS_SLEEP: "The enumeration “sleep” is asserted |
| 781 |
* true when the PoDL PSE state diagram variable pi_sleeping is true." |
| 782 |
* @ETHTOOL_PODL_PSE_PW_D_STATUS_IDLE: "The enumeration “idle” is asserted true |
| 783 |
* when the logical combination of the PoDL PSE state diagram variables |
| 784 |
* pi_prebiased*!pi_sleeping is true." |
| 785 |
* @ETHTOOL_PODL_PSE_PW_D_STATUS_ERROR: "The enumeration “error” is asserted |
| 786 |
* true when the PoDL PSE state diagram variable overload_held is true." |
| 787 |
*/ |
| 788 |
enum ethtool_podl_pse_pw_d_status { |
| 789 |
ETHTOOL_PODL_PSE_PW_D_STATUS_UNKNOWN = 1, |
| 790 |
ETHTOOL_PODL_PSE_PW_D_STATUS_DISABLED, |
| 791 |
ETHTOOL_PODL_PSE_PW_D_STATUS_SEARCHING, |
| 792 |
ETHTOOL_PODL_PSE_PW_D_STATUS_DELIVERING, |
| 793 |
ETHTOOL_PODL_PSE_PW_D_STATUS_SLEEP, |
| 794 |
ETHTOOL_PODL_PSE_PW_D_STATUS_IDLE, |
| 795 |
ETHTOOL_PODL_PSE_PW_D_STATUS_ERROR, |
| 796 |
}; |
| 797 |
|
| 798 |
/** |
| 799 |
* enum ethtool_mm_verify_status - status of MAC Merge Verify function |
| 800 |
* @ETHTOOL_MM_VERIFY_STATUS_UNKNOWN: |
| 801 |
* verification status is unknown |
| 802 |
* @ETHTOOL_MM_VERIFY_STATUS_INITIAL: |
| 803 |
* the 802.3 Verify State diagram is in the state INIT_VERIFICATION |
| 804 |
* @ETHTOOL_MM_VERIFY_STATUS_VERIFYING: |
| 805 |
* the Verify State diagram is in the state VERIFICATION_IDLE, |
| 806 |
* SEND_VERIFY or WAIT_FOR_RESPONSE |
| 807 |
* @ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED: |
| 808 |
* indicates that the Verify State diagram is in the state VERIFIED |
| 809 |
* @ETHTOOL_MM_VERIFY_STATUS_FAILED: |
| 810 |
* the Verify State diagram is in the state VERIFY_FAIL |
| 811 |
* @ETHTOOL_MM_VERIFY_STATUS_DISABLED: |
| 812 |
* verification of preemption operation is disabled |
| 813 |
*/ |
| 814 |
enum ethtool_mm_verify_status { |
| 815 |
ETHTOOL_MM_VERIFY_STATUS_UNKNOWN, |
| 816 |
ETHTOOL_MM_VERIFY_STATUS_INITIAL, |
| 817 |
ETHTOOL_MM_VERIFY_STATUS_VERIFYING, |
| 818 |
ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED, |
| 819 |
ETHTOOL_MM_VERIFY_STATUS_FAILED, |
| 820 |
ETHTOOL_MM_VERIFY_STATUS_DISABLED, |
| 821 |
}; |
| 822 |
|
| 823 |
/** |
| 824 |
* struct ethtool_gstrings - string set for data tagging |
| 825 |
* @cmd: Command number = %ETHTOOL_GSTRINGS |
| 826 |
* @string_set: String set ID; one of &enum ethtool_stringset |
| 827 |
* @len: On return, the number of strings in the string set |
| 828 |
* @data: Buffer for strings. Each string is null-padded to a size of |
| 829 |
* %ETH_GSTRING_LEN. |
| 830 |
* |
| 831 |
* Users must use %ETHTOOL_GSSET_INFO to find the number of strings in |
| 832 |
* the string set. They must allocate a buffer of the appropriate |
| 833 |
* size immediately following this structure. |
| 834 |
*/ |
| 835 |
struct ethtool_gstrings { |
| 836 |
__u32 cmd; |
| 837 |
__u32 string_set; |
| 838 |
__u32 len; |
| 839 |
__u8 data[]; |
| 840 |
}; |
| 841 |
|
| 842 |
/** |
| 843 |
* struct ethtool_sset_info - string set information |
| 844 |
* @cmd: Command number = %ETHTOOL_GSSET_INFO |
| 845 |
* @reserved: Reserved for future use; see the note on reserved space. |
| 846 |
* @sset_mask: On entry, a bitmask of string sets to query, with bits |
| 847 |
* numbered according to &enum ethtool_stringset. On return, a |
| 848 |
* bitmask of those string sets queried that are supported. |
| 849 |
* @data: Buffer for string set sizes. On return, this contains the |
| 850 |
* size of each string set that was queried and supported, in |
| 851 |
* order of ID. |
| 852 |
* |
| 853 |
* Example: The user passes in @sset_mask = 0x7 (sets 0, 1, 2) and on |
| 854 |
* return @sset_mask == 0x6 (sets 1, 2). Then @data[0] contains the |
| 855 |
* size of set 1 and @data[1] contains the size of set 2. |
| 856 |
* |
| 857 |
* Users must allocate a buffer of the appropriate size (4 * number of |
| 858 |
* sets queried) immediately following this structure. |
| 859 |
*/ |
| 860 |
struct ethtool_sset_info { |
| 861 |
__u32 cmd; |
| 862 |
__u32 reserved; |
| 863 |
__u64 sset_mask; |
| 864 |
__u32 data[]; |
| 865 |
}; |
| 866 |
|
| 867 |
/** |
| 868 |
* enum ethtool_test_flags - flags definition of ethtool_test |
| 869 |
* @ETH_TEST_FL_OFFLINE: if set perform online and offline tests, otherwise |
| 870 |
* only online tests. |
| 871 |
* @ETH_TEST_FL_FAILED: Driver set this flag if test fails. |
| 872 |
* @ETH_TEST_FL_EXTERNAL_LB: Application request to perform external loopback |
| 873 |
* test. |
| 874 |
* @ETH_TEST_FL_EXTERNAL_LB_DONE: Driver performed the external loopback test |
| 875 |
*/ |
| 876 |
|
| 877 |
enum ethtool_test_flags { |
| 878 |
ETH_TEST_FL_OFFLINE = (1 << 0), |
| 879 |
ETH_TEST_FL_FAILED = (1 << 1), |
| 880 |
ETH_TEST_FL_EXTERNAL_LB = (1 << 2), |
| 881 |
ETH_TEST_FL_EXTERNAL_LB_DONE = (1 << 3), |
| 882 |
}; |
| 883 |
|
| 884 |
/** |
| 885 |
* struct ethtool_test - device self-test invocation |
| 886 |
* @cmd: Command number = %ETHTOOL_TEST |
| 887 |
* @flags: A bitmask of flags from &enum ethtool_test_flags. Some |
| 888 |
* flags may be set by the user on entry; others may be set by |
| 889 |
* the driver on return. |
| 890 |
* @reserved: Reserved for future use; see the note on reserved space. |
| 891 |
* @len: On return, the number of test results |
| 892 |
* @data: Array of test results |
| 893 |
* |
| 894 |
* Users must use %ETHTOOL_GSSET_INFO or %ETHTOOL_GDRVINFO to find the |
| 895 |
* number of test results that will be returned. They must allocate a |
| 896 |
* buffer of the appropriate size (8 * number of results) immediately |
| 897 |
* following this structure. |
| 898 |
*/ |
| 899 |
struct ethtool_test { |
| 900 |
__u32 cmd; |
| 901 |
__u32 flags; |
| 902 |
__u32 reserved; |
| 903 |
__u32 len; |
| 904 |
__u64 data[]; |
| 905 |
}; |
| 906 |
|
| 907 |
/** |
| 908 |
* struct ethtool_stats - device-specific statistics |
| 909 |
* @cmd: Command number = %ETHTOOL_GSTATS |
| 910 |
* @n_stats: On return, the number of statistics |
| 911 |
* @data: Array of statistics |
| 912 |
* |
| 913 |
* Users must use %ETHTOOL_GSSET_INFO or %ETHTOOL_GDRVINFO to find the |
| 914 |
* number of statistics that will be returned. They must allocate a |
| 915 |
* buffer of the appropriate size (8 * number of statistics) |
| 916 |
* immediately following this structure. |
| 917 |
*/ |
| 918 |
struct ethtool_stats { |
| 919 |
__u32 cmd; |
| 920 |
__u32 n_stats; |
| 921 |
__u64 data[]; |
| 922 |
}; |
| 923 |
|
| 924 |
/** |
| 925 |
* struct ethtool_perm_addr - permanent hardware address |
| 926 |
* @cmd: Command number = %ETHTOOL_GPERMADDR |
| 927 |
* @size: On entry, the size of the buffer. On return, the size of the |
| 928 |
* address. The command fails if the buffer is too small. |
| 929 |
* @data: Buffer for the address |
| 930 |
* |
| 931 |
* Users must allocate the buffer immediately following this structure. |
| 932 |
* A buffer size of %MAX_ADDR_LEN should be sufficient for any address |
| 933 |
* type. |
| 934 |
*/ |
| 935 |
struct ethtool_perm_addr { |
| 936 |
__u32 cmd; |
| 937 |
__u32 size; |
| 938 |
__u8 data[]; |
| 939 |
}; |
| 940 |
|
| 941 |
/* boolean flags controlling per-interface behavior characteristics. |
| 942 |
* When reading, the flag indicates whether or not a certain behavior |
| 943 |
* is enabled/present. When writing, the flag indicates whether |
| 944 |
* or not the driver should turn on (set) or off (clear) a behavior. |
| 945 |
* |
| 946 |
* Some behaviors may read-only (unconditionally absent or present). |
| 947 |
* If such is the case, return EINVAL in the set-flags operation if the |
| 948 |
* flag differs from the read-only value. |
| 949 |
*/ |
| 950 |
enum ethtool_flags { |
| 951 |
ETH_FLAG_TXVLAN = (1 << 7), /* TX VLAN offload enabled */ |
| 952 |
ETH_FLAG_RXVLAN = (1 << 8), /* RX VLAN offload enabled */ |
| 953 |
ETH_FLAG_LRO = (1 << 15), /* LRO is enabled */ |
| 954 |
ETH_FLAG_NTUPLE = (1 << 27), /* N-tuple filters enabled */ |
| 955 |
ETH_FLAG_RXHASH = (1 << 28), |
| 956 |
}; |
| 957 |
|
| 958 |
/* The following structures are for supporting RX network flow |
| 959 |
* classification and RX n-tuple configuration. Note, all multibyte |
| 960 |
* fields, e.g., ip4src, ip4dst, psrc, pdst, spi, etc. are expected to |
| 961 |
* be in network byte order. |
| 962 |
*/ |
| 963 |
|
| 964 |
/** |
| 965 |
* struct ethtool_tcpip4_spec - flow specification for TCP/IPv4 etc. |
| 966 |
* @ip4src: Source host |
| 967 |
* @ip4dst: Destination host |
| 968 |
* @psrc: Source port |
| 969 |
* @pdst: Destination port |
| 970 |
* @tos: Type-of-service |
| 971 |
* |
| 972 |
* This can be used to specify a TCP/IPv4, UDP/IPv4 or SCTP/IPv4 flow. |
| 973 |
*/ |
| 974 |
struct ethtool_tcpip4_spec { |
| 975 |
__be32 ip4src; |
| 976 |
__be32 ip4dst; |
| 977 |
__be16 psrc; |
| 978 |
__be16 pdst; |
| 979 |
__u8 tos; |
| 980 |
}; |
| 981 |
|
| 982 |
/** |
| 983 |
* struct ethtool_ah_espip4_spec - flow specification for IPsec/IPv4 |
| 984 |
* @ip4src: Source host |
| 985 |
* @ip4dst: Destination host |
| 986 |
* @spi: Security parameters index |
| 987 |
* @tos: Type-of-service |
| 988 |
* |
| 989 |
* This can be used to specify an IPsec transport or tunnel over IPv4. |
| 990 |
*/ |
| 991 |
struct ethtool_ah_espip4_spec { |
| 992 |
__be32 ip4src; |
| 993 |
__be32 ip4dst; |
| 994 |
__be32 spi; |
| 995 |
__u8 tos; |
| 996 |
}; |
| 997 |
|
| 998 |
#define ETH_RX_NFC_IP4 1 |
| 999 |
|
| 1000 |
/** |
| 1001 |
* struct ethtool_usrip4_spec - general flow specification for IPv4 |
| 1002 |
* @ip4src: Source host |
| 1003 |
* @ip4dst: Destination host |
| 1004 |
* @l4_4_bytes: First 4 bytes of transport (layer 4) header |
| 1005 |
* @tos: Type-of-service |
| 1006 |
* @ip_ver: Value must be %ETH_RX_NFC_IP4; mask must be 0 |
| 1007 |
* @proto: Transport protocol number; mask must be 0 |
| 1008 |
*/ |
| 1009 |
struct ethtool_usrip4_spec { |
| 1010 |
__be32 ip4src; |
| 1011 |
__be32 ip4dst; |
| 1012 |
__be32 l4_4_bytes; |
| 1013 |
__u8 tos; |
| 1014 |
__u8 ip_ver; |
| 1015 |
__u8 proto; |
| 1016 |
}; |
| 1017 |
|
| 1018 |
/** |
| 1019 |
* struct ethtool_tcpip6_spec - flow specification for TCP/IPv6 etc. |
| 1020 |
* @ip6src: Source host |
| 1021 |
* @ip6dst: Destination host |
| 1022 |
* @psrc: Source port |
| 1023 |
* @pdst: Destination port |
| 1024 |
* @tclass: Traffic Class |
| 1025 |
* |
| 1026 |
* This can be used to specify a TCP/IPv6, UDP/IPv6 or SCTP/IPv6 flow. |
| 1027 |
*/ |
| 1028 |
struct ethtool_tcpip6_spec { |
| 1029 |
__be32 ip6src[4]; |
| 1030 |
__be32 ip6dst[4]; |
| 1031 |
__be16 psrc; |
| 1032 |
__be16 pdst; |
| 1033 |
__u8 tclass; |
| 1034 |
}; |
| 1035 |
|
| 1036 |
/** |
| 1037 |
* struct ethtool_ah_espip6_spec - flow specification for IPsec/IPv6 |
| 1038 |
* @ip6src: Source host |
| 1039 |
* @ip6dst: Destination host |
| 1040 |
* @spi: Security parameters index |
| 1041 |
* @tclass: Traffic Class |
| 1042 |
* |
| 1043 |
* This can be used to specify an IPsec transport or tunnel over IPv6. |
| 1044 |
*/ |
| 1045 |
struct ethtool_ah_espip6_spec { |
| 1046 |
__be32 ip6src[4]; |
| 1047 |
__be32 ip6dst[4]; |
| 1048 |
__be32 spi; |
| 1049 |
__u8 tclass; |
| 1050 |
}; |
| 1051 |
|
| 1052 |
/** |
| 1053 |
* struct ethtool_usrip6_spec - general flow specification for IPv6 |
| 1054 |
* @ip6src: Source host |
| 1055 |
* @ip6dst: Destination host |
| 1056 |
* @l4_4_bytes: First 4 bytes of transport (layer 4) header |
| 1057 |
* @tclass: Traffic Class |
| 1058 |
* @l4_proto: Transport protocol number (nexthdr after any Extension Headers) |
| 1059 |
*/ |
| 1060 |
struct ethtool_usrip6_spec { |
| 1061 |
__be32 ip6src[4]; |
| 1062 |
__be32 ip6dst[4]; |
| 1063 |
__be32 l4_4_bytes; |
| 1064 |
__u8 tclass; |
| 1065 |
__u8 l4_proto; |
| 1066 |
}; |
| 1067 |
|
| 1068 |
union ethtool_flow_union { |
| 1069 |
struct ethtool_tcpip4_spec tcp_ip4_spec; |
| 1070 |
struct ethtool_tcpip4_spec udp_ip4_spec; |
| 1071 |
struct ethtool_tcpip4_spec sctp_ip4_spec; |
| 1072 |
struct ethtool_ah_espip4_spec ah_ip4_spec; |
| 1073 |
struct ethtool_ah_espip4_spec esp_ip4_spec; |
| 1074 |
struct ethtool_usrip4_spec usr_ip4_spec; |
| 1075 |
struct ethtool_tcpip6_spec tcp_ip6_spec; |
| 1076 |
struct ethtool_tcpip6_spec udp_ip6_spec; |
| 1077 |
struct ethtool_tcpip6_spec sctp_ip6_spec; |
| 1078 |
struct ethtool_ah_espip6_spec ah_ip6_spec; |
| 1079 |
struct ethtool_ah_espip6_spec esp_ip6_spec; |
| 1080 |
struct ethtool_usrip6_spec usr_ip6_spec; |
| 1081 |
struct ethhdr ether_spec; |
| 1082 |
__u8 hdata[52]; |
| 1083 |
}; |
| 1084 |
|
| 1085 |
/** |
| 1086 |
* struct ethtool_flow_ext - additional RX flow fields |
| 1087 |
* @h_dest: destination MAC address |
| 1088 |
* @vlan_etype: VLAN EtherType |
| 1089 |
* @vlan_tci: VLAN tag control information |
| 1090 |
* @data: user defined data |
| 1091 |
* @padding: Reserved for future use; see the note on reserved space. |
| 1092 |
* |
| 1093 |
* Note, @vlan_etype, @vlan_tci, and @data are only valid if %FLOW_EXT |
| 1094 |
* is set in &struct ethtool_rx_flow_spec @flow_type. |
| 1095 |
* @h_dest is valid if %FLOW_MAC_EXT is set. |
| 1096 |
*/ |
| 1097 |
struct ethtool_flow_ext { |
| 1098 |
__u8 padding[2]; |
| 1099 |
unsigned char h_dest[ETH_ALEN]; |
| 1100 |
__be16 vlan_etype; |
| 1101 |
__be16 vlan_tci; |
| 1102 |
__be32 data[2]; |
| 1103 |
}; |
| 1104 |
|
| 1105 |
/** |
| 1106 |
* struct ethtool_rx_flow_spec - classification rule for RX flows |
| 1107 |
* @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW |
| 1108 |
* @h_u: Flow fields to match (dependent on @flow_type) |
| 1109 |
* @h_ext: Additional fields to match |
| 1110 |
* @m_u: Masks for flow field bits to be matched |
| 1111 |
* @m_ext: Masks for additional field bits to be matched |
| 1112 |
* Note, all additional fields must be ignored unless @flow_type |
| 1113 |
* includes the %FLOW_EXT or %FLOW_MAC_EXT flag |
| 1114 |
* (see &struct ethtool_flow_ext description). |
| 1115 |
* @ring_cookie: RX ring/queue index to deliver to, or %RX_CLS_FLOW_DISC |
| 1116 |
* if packets should be discarded, or %RX_CLS_FLOW_WAKE if the |
| 1117 |
* packets should be used for Wake-on-LAN with %WAKE_FILTER |
| 1118 |
* @location: Location of rule in the table. Locations must be |
| 1119 |
* numbered such that a flow matching multiple rules will be |
| 1120 |
* classified according to the first (lowest numbered) rule. |
| 1121 |
*/ |
| 1122 |
struct ethtool_rx_flow_spec { |
| 1123 |
__u32 flow_type; |
| 1124 |
union ethtool_flow_union h_u; |
| 1125 |
struct ethtool_flow_ext h_ext; |
| 1126 |
union ethtool_flow_union m_u; |
| 1127 |
struct ethtool_flow_ext m_ext; |
| 1128 |
__u64 ring_cookie; |
| 1129 |
__u32 location; |
| 1130 |
}; |
| 1131 |
|
| 1132 |
/* How rings are laid out when accessing virtual functions or |
| 1133 |
* offloaded queues is device specific. To allow users to do flow |
| 1134 |
* steering and specify these queues the ring cookie is partitioned |
| 1135 |
* into a 32bit queue index with an 8 bit virtual function id. |
| 1136 |
* This also leaves the 3bytes for further specifiers. It is possible |
| 1137 |
* future devices may support more than 256 virtual functions if |
| 1138 |
* devices start supporting PCIe w/ARI. However at the moment I |
| 1139 |
* do not know of any devices that support this so I do not reserve |
| 1140 |
* space for this at this time. If a future patch consumes the next |
| 1141 |
* byte it should be aware of this possibility. |
| 1142 |
*/ |
| 1143 |
#define ETHTOOL_RX_FLOW_SPEC_RING 0x00000000FFFFFFFFLL |
| 1144 |
#define ETHTOOL_RX_FLOW_SPEC_RING_VF 0x000000FF00000000LL |
| 1145 |
#define ETHTOOL_RX_FLOW_SPEC_RING_VF_OFF 32 |
| 1146 |
static __inline__ __u64 ethtool_get_flow_spec_ring(__u64 ring_cookie) |
| 1147 |
{ |
| 1148 |
return ETHTOOL_RX_FLOW_SPEC_RING & ring_cookie; |
| 1149 |
} |
| 1150 |
|
| 1151 |
static __inline__ __u64 ethtool_get_flow_spec_ring_vf(__u64 ring_cookie) |
| 1152 |
{ |
| 1153 |
return (ETHTOOL_RX_FLOW_SPEC_RING_VF & ring_cookie) >> |
| 1154 |
ETHTOOL_RX_FLOW_SPEC_RING_VF_OFF; |
| 1155 |
} |
| 1156 |
|
| 1157 |
/** |
| 1158 |
* struct ethtool_rxnfc - command to get or set RX flow classification rules |
| 1159 |
* @cmd: Specific command number - %ETHTOOL_GRXFH, %ETHTOOL_SRXFH, |
| 1160 |
* %ETHTOOL_GRXRINGS, %ETHTOOL_GRXCLSRLCNT, %ETHTOOL_GRXCLSRULE, |
| 1161 |
* %ETHTOOL_GRXCLSRLALL, %ETHTOOL_SRXCLSRLDEL or %ETHTOOL_SRXCLSRLINS |
| 1162 |
* @flow_type: Type of flow to be affected, e.g. %TCP_V4_FLOW |
| 1163 |
* @data: Command-dependent value |
| 1164 |
* @fs: Flow classification rule |
| 1165 |
* @rss_context: RSS context to be affected |
| 1166 |
* @rule_cnt: Number of rules to be affected |
| 1167 |
* @rule_locs: Array of used rule locations |
| 1168 |
* |
| 1169 |
* For %ETHTOOL_GRXFH and %ETHTOOL_SRXFH, @data is a bitmask indicating |
| 1170 |
* the fields included in the flow hash, e.g. %RXH_IP_SRC. The following |
| 1171 |
* structure fields must not be used, except that if @flow_type includes |
| 1172 |
* the %FLOW_RSS flag, then @rss_context determines which RSS context to |
| 1173 |
* act on. |
| 1174 |
* |
| 1175 |
* For %ETHTOOL_GRXRINGS, @data is set to the number of RX rings/queues |
| 1176 |
* on return. |
| 1177 |
* |
| 1178 |
* For %ETHTOOL_GRXCLSRLCNT, @rule_cnt is set to the number of defined |
| 1179 |
* rules on return. If @data is non-zero on return then it is the |
| 1180 |
* size of the rule table, plus the flag %RX_CLS_LOC_SPECIAL if the |
| 1181 |
* driver supports any special location values. If that flag is not |
| 1182 |
* set in @data then special location values should not be used. |
| 1183 |
* |
| 1184 |
* For %ETHTOOL_GRXCLSRULE, @fs.@location specifies the location of an |
| 1185 |
* existing rule on entry and @fs contains the rule on return; if |
| 1186 |
* @fs.@flow_type includes the %FLOW_RSS flag, then @rss_context is |
| 1187 |
* filled with the RSS context ID associated with the rule. |
| 1188 |
* |
| 1189 |
* For %ETHTOOL_GRXCLSRLALL, @rule_cnt specifies the array size of the |
| 1190 |
* user buffer for @rule_locs on entry. On return, @data is the size |
| 1191 |
* of the rule table, @rule_cnt is the number of defined rules, and |
| 1192 |
* @rule_locs contains the locations of the defined rules. Drivers |
| 1193 |
* must use the second parameter to get_rxnfc() instead of @rule_locs. |
| 1194 |
* |
| 1195 |
* For %ETHTOOL_SRXCLSRLINS, @fs specifies the rule to add or update. |
| 1196 |
* @fs.@location either specifies the location to use or is a special |
| 1197 |
* location value with %RX_CLS_LOC_SPECIAL flag set. On return, |
| 1198 |
* @fs.@location is the actual rule location. If @fs.@flow_type |
| 1199 |
* includes the %FLOW_RSS flag, @rss_context is the RSS context ID to |
| 1200 |
* use for flow spreading traffic which matches this rule. The value |
| 1201 |
* from the rxfh indirection table will be added to @fs.@ring_cookie |
| 1202 |
* to choose which ring to deliver to. |
| 1203 |
* |
| 1204 |
* For %ETHTOOL_SRXCLSRLDEL, @fs.@location specifies the location of an |
| 1205 |
* existing rule on entry. |
| 1206 |
* |
| 1207 |
* A driver supporting the special location values for |
| 1208 |
* %ETHTOOL_SRXCLSRLINS may add the rule at any suitable unused |
| 1209 |
* location, and may remove a rule at a later location (lower |
| 1210 |
* priority) that matches exactly the same set of flows. The special |
| 1211 |
* values are %RX_CLS_LOC_ANY, selecting any location; |
| 1212 |
* %RX_CLS_LOC_FIRST, selecting the first suitable location (maximum |
| 1213 |
* priority); and %RX_CLS_LOC_LAST, selecting the last suitable |
| 1214 |
* location (minimum priority). Additional special values may be |
| 1215 |
* defined in future and drivers must return -%EINVAL for any |
| 1216 |
* unrecognised value. |
| 1217 |
*/ |
| 1218 |
struct ethtool_rxnfc { |
| 1219 |
__u32 cmd; |
| 1220 |
__u32 flow_type; |
| 1221 |
__u64 data; |
| 1222 |
struct ethtool_rx_flow_spec fs; |
| 1223 |
union { |
| 1224 |
__u32 rule_cnt; |
| 1225 |
__u32 rss_context; |
| 1226 |
}; |
| 1227 |
__u32 rule_locs[]; |
| 1228 |
}; |
| 1229 |
|
| 1230 |
|
| 1231 |
/** |
| 1232 |
* struct ethtool_rxfh_indir - command to get or set RX flow hash indirection |
| 1233 |
* @cmd: Specific command number - %ETHTOOL_GRXFHINDIR or %ETHTOOL_SRXFHINDIR |
| 1234 |
* @size: On entry, the array size of the user buffer, which may be zero. |
| 1235 |
* On return from %ETHTOOL_GRXFHINDIR, the array size of the hardware |
| 1236 |
* indirection table. |
| 1237 |
* @ring_index: RX ring/queue index for each hash value |
| 1238 |
* |
| 1239 |
* For %ETHTOOL_GRXFHINDIR, a @size of zero means that only the size |
| 1240 |
* should be returned. For %ETHTOOL_SRXFHINDIR, a @size of zero means |
| 1241 |
* the table should be reset to default values. This last feature |
| 1242 |
* is not supported by the original implementations. |
| 1243 |
*/ |
| 1244 |
struct ethtool_rxfh_indir { |
| 1245 |
__u32 cmd; |
| 1246 |
__u32 size; |
| 1247 |
__u32 ring_index[]; |
| 1248 |
}; |
| 1249 |
|
| 1250 |
/** |
| 1251 |
* struct ethtool_rxfh - command to get/set RX flow hash indir or/and hash key. |
| 1252 |
* @cmd: Specific command number - %ETHTOOL_GRSSH or %ETHTOOL_SRSSH |
| 1253 |
* @rss_context: RSS context identifier. Context 0 is the default for normal |
| 1254 |
* traffic; other contexts can be referenced as the destination for RX flow |
| 1255 |
* classification rules. %ETH_RXFH_CONTEXT_ALLOC is used with command |
| 1256 |
* %ETHTOOL_SRSSH to allocate a new RSS context; on return this field will |
| 1257 |
* contain the ID of the newly allocated context. |
| 1258 |
* @indir_size: On entry, the array size of the user buffer for the |
| 1259 |
* indirection table, which may be zero, or (for %ETHTOOL_SRSSH), |
| 1260 |
* %ETH_RXFH_INDIR_NO_CHANGE. On return from %ETHTOOL_GRSSH, |
| 1261 |
* the array size of the hardware indirection table. |
| 1262 |
* @key_size: On entry, the array size of the user buffer for the hash key, |
| 1263 |
* which may be zero. On return from %ETHTOOL_GRSSH, the size of the |
| 1264 |
* hardware hash key. |
| 1265 |
* @hfunc: Defines the current RSS hash function used by HW (or to be set to). |
| 1266 |
* Valid values are one of the %ETH_RSS_HASH_*. |
| 1267 |
* @rsvd8: Reserved for future use; see the note on reserved space. |
| 1268 |
* @rsvd32: Reserved for future use; see the note on reserved space. |
| 1269 |
* @rss_config: RX ring/queue index for each hash value i.e., indirection table |
| 1270 |
* of @indir_size __u32 elements, followed by hash key of @key_size |
| 1271 |
* bytes. |
| 1272 |
* |
| 1273 |
* For %ETHTOOL_GRSSH, a @indir_size and key_size of zero means that only the |
| 1274 |
* size should be returned. For %ETHTOOL_SRSSH, an @indir_size of |
| 1275 |
* %ETH_RXFH_INDIR_NO_CHANGE means that indir table setting is not requested |
| 1276 |
* and a @indir_size of zero means the indir table should be reset to default |
| 1277 |
* values (if @rss_context == 0) or that the RSS context should be deleted. |
| 1278 |
* An hfunc of zero means that hash function setting is not requested. |
| 1279 |
*/ |
| 1280 |
struct ethtool_rxfh { |
| 1281 |
__u32 cmd; |
| 1282 |
__u32 rss_context; |
| 1283 |
__u32 indir_size; |
| 1284 |
__u32 key_size; |
| 1285 |
__u8 hfunc; |
| 1286 |
__u8 rsvd8[3]; |
| 1287 |
__u32 rsvd32; |
| 1288 |
__u32 rss_config[]; |
| 1289 |
}; |
| 1290 |
#define ETH_RXFH_CONTEXT_ALLOC 0xffffffff |
| 1291 |
#define ETH_RXFH_INDIR_NO_CHANGE 0xffffffff |
| 1292 |
|
| 1293 |
/** |
| 1294 |
* struct ethtool_rx_ntuple_flow_spec - specification for RX flow filter |
| 1295 |
* @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW |
| 1296 |
* @h_u: Flow field values to match (dependent on @flow_type) |
| 1297 |
* @m_u: Masks for flow field value bits to be ignored |
| 1298 |
* @vlan_tag: VLAN tag to match |
| 1299 |
* @vlan_tag_mask: Mask for VLAN tag bits to be ignored |
| 1300 |
* @data: Driver-dependent data to match |
| 1301 |
* @data_mask: Mask for driver-dependent data bits to be ignored |
| 1302 |
* @action: RX ring/queue index to deliver to (non-negative) or other action |
| 1303 |
* (negative, e.g. %ETHTOOL_RXNTUPLE_ACTION_DROP) |
| 1304 |
* |
| 1305 |
* For flow types %TCP_V4_FLOW, %UDP_V4_FLOW and %SCTP_V4_FLOW, where |
| 1306 |
* a field value and mask are both zero this is treated as if all mask |
| 1307 |
* bits are set i.e. the field is ignored. |
| 1308 |
*/ |
| 1309 |
struct ethtool_rx_ntuple_flow_spec { |
| 1310 |
__u32 flow_type; |
| 1311 |
union { |
| 1312 |
struct ethtool_tcpip4_spec tcp_ip4_spec; |
| 1313 |
struct ethtool_tcpip4_spec udp_ip4_spec; |
| 1314 |
struct ethtool_tcpip4_spec sctp_ip4_spec; |
| 1315 |
struct ethtool_ah_espip4_spec ah_ip4_spec; |
| 1316 |
struct ethtool_ah_espip4_spec esp_ip4_spec; |
| 1317 |
struct ethtool_usrip4_spec usr_ip4_spec; |
| 1318 |
struct ethhdr ether_spec; |
| 1319 |
__u8 hdata[72]; |
| 1320 |
} h_u, m_u; |
| 1321 |
|
| 1322 |
__u16 vlan_tag; |
| 1323 |
__u16 vlan_tag_mask; |
| 1324 |
__u64 data; |
| 1325 |
__u64 data_mask; |
| 1326 |
|
| 1327 |
__s32 action; |
| 1328 |
#define ETHTOOL_RXNTUPLE_ACTION_DROP (-1) /* drop packet */ |
| 1329 |
#define ETHTOOL_RXNTUPLE_ACTION_CLEAR (-2) /* clear filter */ |
| 1330 |
}; |
| 1331 |
|
| 1332 |
/** |
| 1333 |
* struct ethtool_rx_ntuple - command to set or clear RX flow filter |
| 1334 |
* @cmd: Command number - %ETHTOOL_SRXNTUPLE |
| 1335 |
* @fs: Flow filter specification |
| 1336 |
*/ |
| 1337 |
struct ethtool_rx_ntuple { |
| 1338 |
__u32 cmd; |
| 1339 |
struct ethtool_rx_ntuple_flow_spec fs; |
| 1340 |
}; |
| 1341 |
|
| 1342 |
#define ETHTOOL_FLASH_MAX_FILENAME 128 |
| 1343 |
enum ethtool_flash_op_type { |
| 1344 |
ETHTOOL_FLASH_ALL_REGIONS = 0, |
| 1345 |
}; |
| 1346 |
|
| 1347 |
/* for passing firmware flashing related parameters */ |
| 1348 |
struct ethtool_flash { |
| 1349 |
__u32 cmd; |
| 1350 |
__u32 region; |
| 1351 |
char data[ETHTOOL_FLASH_MAX_FILENAME]; |
| 1352 |
}; |
| 1353 |
|
| 1354 |
/** |
| 1355 |
* struct ethtool_dump - used for retrieving, setting device dump |
| 1356 |
* @cmd: Command number - %ETHTOOL_GET_DUMP_FLAG, %ETHTOOL_GET_DUMP_DATA, or |
| 1357 |
* %ETHTOOL_SET_DUMP |
| 1358 |
* @version: FW version of the dump, filled in by driver |
| 1359 |
* @flag: driver dependent flag for dump setting, filled in by driver during |
| 1360 |
* get and filled in by ethtool for set operation. |
| 1361 |
* flag must be initialized by macro ETH_FW_DUMP_DISABLE value when |
| 1362 |
* firmware dump is disabled. |
| 1363 |
* @len: length of dump data, used as the length of the user buffer on entry to |
| 1364 |
* %ETHTOOL_GET_DUMP_DATA and this is returned as dump length by driver |
| 1365 |
* for %ETHTOOL_GET_DUMP_FLAG command |
| 1366 |
* @data: data collected for get dump data operation |
| 1367 |
*/ |
| 1368 |
struct ethtool_dump { |
| 1369 |
__u32 cmd; |
| 1370 |
__u32 version; |
| 1371 |
__u32 flag; |
| 1372 |
__u32 len; |
| 1373 |
__u8 data[]; |
| 1374 |
}; |
| 1375 |
|
| 1376 |
#define ETH_FW_DUMP_DISABLE 0 |
| 1377 |
|
| 1378 |
/* for returning and changing feature sets */ |
| 1379 |
|
| 1380 |
/** |
| 1381 |
* struct ethtool_get_features_block - block with state of 32 features |
| 1382 |
* @available: mask of changeable features |
| 1383 |
* @requested: mask of features requested to be enabled if possible |
| 1384 |
* @active: mask of currently enabled features |
| 1385 |
* @never_changed: mask of features not changeable for any device |
| 1386 |
*/ |
| 1387 |
struct ethtool_get_features_block { |
| 1388 |
__u32 available; |
| 1389 |
__u32 requested; |
| 1390 |
__u32 active; |
| 1391 |
__u32 never_changed; |
| 1392 |
}; |
| 1393 |
|
| 1394 |
/** |
| 1395 |
* struct ethtool_gfeatures - command to get state of device's features |
| 1396 |
* @cmd: command number = %ETHTOOL_GFEATURES |
| 1397 |
* @size: On entry, the number of elements in the features[] array; |
| 1398 |
* on return, the number of elements in features[] needed to hold |
| 1399 |
* all features |
| 1400 |
* @features: state of features |
| 1401 |
*/ |
| 1402 |
struct ethtool_gfeatures { |
| 1403 |
__u32 cmd; |
| 1404 |
__u32 size; |
| 1405 |
struct ethtool_get_features_block features[]; |
| 1406 |
}; |
| 1407 |
|
| 1408 |
/** |
| 1409 |
* struct ethtool_set_features_block - block with request for 32 features |
| 1410 |
* @valid: mask of features to be changed |
| 1411 |
* @requested: values of features to be changed |
| 1412 |
*/ |
| 1413 |
struct ethtool_set_features_block { |
| 1414 |
__u32 valid; |
| 1415 |
__u32 requested; |
| 1416 |
}; |
| 1417 |
|
| 1418 |
/** |
| 1419 |
* struct ethtool_sfeatures - command to request change in device's features |
| 1420 |
* @cmd: command number = %ETHTOOL_SFEATURES |
| 1421 |
* @size: array size of the features[] array |
| 1422 |
* @features: feature change masks |
| 1423 |
*/ |
| 1424 |
struct ethtool_sfeatures { |
| 1425 |
__u32 cmd; |
| 1426 |
__u32 size; |
| 1427 |
struct ethtool_set_features_block features[]; |
| 1428 |
}; |
| 1429 |
|
| 1430 |
/** |
| 1431 |
* struct ethtool_ts_info - holds a device's timestamping and PHC association |
| 1432 |
* @cmd: command number = %ETHTOOL_GET_TS_INFO |
| 1433 |
* @so_timestamping: bit mask of the sum of the supported SO_TIMESTAMPING flags |
| 1434 |
* @phc_index: device index of the associated PHC, or -1 if there is none |
| 1435 |
* @tx_types: bit mask of the supported hwtstamp_tx_types enumeration values |
| 1436 |
* @tx_reserved: Reserved for future use; see the note on reserved space. |
| 1437 |
* @rx_filters: bit mask of the supported hwtstamp_rx_filters enumeration values |
| 1438 |
* @rx_reserved: Reserved for future use; see the note on reserved space. |
| 1439 |
* |
| 1440 |
* The bits in the 'tx_types' and 'rx_filters' fields correspond to |
| 1441 |
* the 'hwtstamp_tx_types' and 'hwtstamp_rx_filters' enumeration values, |
| 1442 |
* respectively. For example, if the device supports HWTSTAMP_TX_ON, |
| 1443 |
* then (1 << HWTSTAMP_TX_ON) in 'tx_types' will be set. |
| 1444 |
* |
| 1445 |
* Drivers should only report the filters they actually support without |
| 1446 |
* upscaling in the SIOCSHWTSTAMP ioctl. If the SIOCSHWSTAMP request for |
| 1447 |
* HWTSTAMP_FILTER_V1_SYNC is supported by HWTSTAMP_FILTER_V1_EVENT, then the |
| 1448 |
* driver should only report HWTSTAMP_FILTER_V1_EVENT in this op. |
| 1449 |
*/ |
| 1450 |
struct ethtool_ts_info { |
| 1451 |
__u32 cmd; |
| 1452 |
__u32 so_timestamping; |
| 1453 |
__s32 phc_index; |
| 1454 |
__u32 tx_types; |
| 1455 |
__u32 tx_reserved[3]; |
| 1456 |
__u32 rx_filters; |
| 1457 |
__u32 rx_reserved[3]; |
| 1458 |
}; |
| 1459 |
|
| 1460 |
/* |
| 1461 |
* %ETHTOOL_SFEATURES changes features present in features[].valid to the |
| 1462 |
* values of corresponding bits in features[].requested. Bits in .requested |
| 1463 |
* not set in .valid or not changeable are ignored. |
| 1464 |
* |
| 1465 |
* Returns %EINVAL when .valid contains undefined or never-changeable bits |
| 1466 |
* or size is not equal to required number of features words (32-bit blocks). |
| 1467 |
* Returns >= 0 if request was completed; bits set in the value mean: |
| 1468 |
* %ETHTOOL_F_UNSUPPORTED - there were bits set in .valid that are not |
| 1469 |
* changeable (not present in %ETHTOOL_GFEATURES' features[].available) |
| 1470 |
* those bits were ignored. |
| 1471 |
* %ETHTOOL_F_WISH - some or all changes requested were recorded but the |
| 1472 |
* resulting state of bits masked by .valid is not equal to .requested. |
| 1473 |
* Probably there are other device-specific constraints on some features |
| 1474 |
* in the set. When %ETHTOOL_F_UNSUPPORTED is set, .valid is considered |
| 1475 |
* here as though ignored bits were cleared. |
| 1476 |
* %ETHTOOL_F_COMPAT - some or all changes requested were made by calling |
| 1477 |
* compatibility functions. Requested offload state cannot be properly |
| 1478 |
* managed by kernel. |
| 1479 |
* |
| 1480 |
* Meaning of bits in the masks are obtained by %ETHTOOL_GSSET_INFO (number of |
| 1481 |
* bits in the arrays - always multiple of 32) and %ETHTOOL_GSTRINGS commands |
| 1482 |
* for ETH_SS_FEATURES string set. First entry in the table corresponds to least |
| 1483 |
* significant bit in features[0] fields. Empty strings mark undefined features. |
| 1484 |
*/ |
| 1485 |
enum ethtool_sfeatures_retval_bits { |
| 1486 |
ETHTOOL_F_UNSUPPORTED__BIT, |
| 1487 |
ETHTOOL_F_WISH__BIT, |
| 1488 |
ETHTOOL_F_COMPAT__BIT, |
| 1489 |
}; |
| 1490 |
|
| 1491 |
#define ETHTOOL_F_UNSUPPORTED (1 << ETHTOOL_F_UNSUPPORTED__BIT) |
| 1492 |
#define ETHTOOL_F_WISH (1 << ETHTOOL_F_WISH__BIT) |
| 1493 |
#define ETHTOOL_F_COMPAT (1 << ETHTOOL_F_COMPAT__BIT) |
| 1494 |
|
| 1495 |
#define MAX_NUM_QUEUE 4096 |
| 1496 |
|
| 1497 |
/** |
| 1498 |
* struct ethtool_per_queue_op - apply sub command to the queues in mask. |
| 1499 |
* @cmd: ETHTOOL_PERQUEUE |
| 1500 |
* @sub_command: the sub command which apply to each queues |
| 1501 |
* @queue_mask: Bitmap of the queues which sub command apply to |
| 1502 |
* @data: A complete command structure following for each of the queues addressed |
| 1503 |
*/ |
| 1504 |
struct ethtool_per_queue_op { |
| 1505 |
__u32 cmd; |
| 1506 |
__u32 sub_command; |
| 1507 |
__u32 queue_mask[__KERNEL_DIV_ROUND_UP(MAX_NUM_QUEUE, 32)]; |
| 1508 |
char data[]; |
| 1509 |
}; |
| 1510 |
|
| 1511 |
/** |
| 1512 |
* struct ethtool_fecparam - Ethernet Forward Error Correction parameters |
| 1513 |
* @cmd: Command number = %ETHTOOL_GFECPARAM or %ETHTOOL_SFECPARAM |
| 1514 |
* @active_fec: FEC mode which is active on the port, single bit set, GET only. |
| 1515 |
* @fec: Bitmask of configured FEC modes. |
| 1516 |
* @reserved: Reserved for future extensions, ignore on GET, write 0 for SET. |
| 1517 |
* |
| 1518 |
* Note that @reserved was never validated on input and ethtool user space |
| 1519 |
* left it uninitialized when calling SET. Hence going forward it can only be |
| 1520 |
* used to return a value to userspace with GET. |
| 1521 |
* |
| 1522 |
* FEC modes supported by the device can be read via %ETHTOOL_GLINKSETTINGS. |
| 1523 |
* FEC settings are configured by link autonegotiation whenever it's enabled. |
| 1524 |
* With autoneg on %ETHTOOL_GFECPARAM can be used to read the current mode. |
| 1525 |
* |
| 1526 |
* When autoneg is disabled %ETHTOOL_SFECPARAM controls the FEC settings. |
| 1527 |
* It is recommended that drivers only accept a single bit set in @fec. |
| 1528 |
* When multiple bits are set in @fec drivers may pick mode in an implementation |
| 1529 |
* dependent way. Drivers should reject mixing %ETHTOOL_FEC_AUTO_BIT with other |
| 1530 |
* FEC modes, because it's unclear whether in this case other modes constrain |
| 1531 |
* AUTO or are independent choices. |
| 1532 |
* Drivers must reject SET requests if they support none of the requested modes. |
| 1533 |
* |
| 1534 |
* If device does not support FEC drivers may use %ETHTOOL_FEC_NONE instead |
| 1535 |
* of returning %EOPNOTSUPP from %ETHTOOL_GFECPARAM. |
| 1536 |
* |
| 1537 |
* See enum ethtool_fec_config_bits for definition of valid bits for both |
| 1538 |
* @fec and @active_fec. |
| 1539 |
*/ |
| 1540 |
struct ethtool_fecparam { |
| 1541 |
__u32 cmd; |
| 1542 |
/* bitmask of FEC modes */ |
| 1543 |
__u32 active_fec; |
| 1544 |
__u32 fec; |
| 1545 |
__u32 reserved; |
| 1546 |
}; |
| 1547 |
|
| 1548 |
/** |
| 1549 |
* enum ethtool_fec_config_bits - flags definition of ethtool_fec_configuration |
| 1550 |
* @ETHTOOL_FEC_NONE_BIT: FEC mode configuration is not supported. Should not |
| 1551 |
* be used together with other bits. GET only. |
| 1552 |
* @ETHTOOL_FEC_AUTO_BIT: Select default/best FEC mode automatically, usually |
| 1553 |
* based link mode and SFP parameters read from module's |
| 1554 |
* EEPROM. This bit does _not_ mean autonegotiation. |
| 1555 |
* @ETHTOOL_FEC_OFF_BIT: No FEC Mode |
| 1556 |
* @ETHTOOL_FEC_RS_BIT: Reed-Solomon FEC Mode |
| 1557 |
* @ETHTOOL_FEC_BASER_BIT: Base-R/Reed-Solomon FEC Mode |
| 1558 |
* @ETHTOOL_FEC_LLRS_BIT: Low Latency Reed Solomon FEC Mode (25G/50G Ethernet |
| 1559 |
* Consortium) |
| 1560 |
*/ |
| 1561 |
enum ethtool_fec_config_bits { |
| 1562 |
ETHTOOL_FEC_NONE_BIT, |
| 1563 |
ETHTOOL_FEC_AUTO_BIT, |
| 1564 |
ETHTOOL_FEC_OFF_BIT, |
| 1565 |
ETHTOOL_FEC_RS_BIT, |
| 1566 |
ETHTOOL_FEC_BASER_BIT, |
| 1567 |
ETHTOOL_FEC_LLRS_BIT, |
| 1568 |
}; |
| 1569 |
|
| 1570 |
#define ETHTOOL_FEC_NONE (1 << ETHTOOL_FEC_NONE_BIT) |
| 1571 |
#define ETHTOOL_FEC_AUTO (1 << ETHTOOL_FEC_AUTO_BIT) |
| 1572 |
#define ETHTOOL_FEC_OFF (1 << ETHTOOL_FEC_OFF_BIT) |
| 1573 |
#define ETHTOOL_FEC_RS (1 << ETHTOOL_FEC_RS_BIT) |
| 1574 |
#define ETHTOOL_FEC_BASER (1 << ETHTOOL_FEC_BASER_BIT) |
| 1575 |
#define ETHTOOL_FEC_LLRS (1 << ETHTOOL_FEC_LLRS_BIT) |
| 1576 |
|
| 1577 |
/* CMDs currently supported */ |
| 1578 |
#define ETHTOOL_GSET 0x00000001 /* DEPRECATED, Get settings. |
| 1579 |
* Please use ETHTOOL_GLINKSETTINGS |
| 1580 |
*/ |
| 1581 |
#define ETHTOOL_SSET 0x00000002 /* DEPRECATED, Set settings. |
| 1582 |
* Please use ETHTOOL_SLINKSETTINGS |
| 1583 |
*/ |
| 1584 |
#define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */ |
| 1585 |
#define ETHTOOL_GREGS 0x00000004 /* Get NIC registers. */ |
| 1586 |
#define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */ |
| 1587 |
#define ETHTOOL_SWOL 0x00000006 /* Set wake-on-lan options. */ |
| 1588 |
#define ETHTOOL_GMSGLVL 0x00000007 /* Get driver message level */ |
| 1589 |
#define ETHTOOL_SMSGLVL 0x00000008 /* Set driver msg level. */ |
| 1590 |
#define ETHTOOL_NWAY_RST 0x00000009 /* Restart autonegotiation. */ |
| 1591 |
/* Get link status for host, i.e. whether the interface *and* the |
| 1592 |
* physical port (if there is one) are up (ethtool_value). */ |
| 1593 |
#define ETHTOOL_GLINK 0x0000000a |
| 1594 |
#define ETHTOOL_GEEPROM 0x0000000b /* Get EEPROM data */ |
| 1595 |
#define ETHTOOL_SEEPROM 0x0000000c /* Set EEPROM data. */ |
| 1596 |
#define ETHTOOL_GCOALESCE 0x0000000e /* Get coalesce config */ |
| 1597 |
#define ETHTOOL_SCOALESCE 0x0000000f /* Set coalesce config. */ |
| 1598 |
#define ETHTOOL_GRINGPARAM 0x00000010 /* Get ring parameters */ |
| 1599 |
#define ETHTOOL_SRINGPARAM 0x00000011 /* Set ring parameters. */ |
| 1600 |
#define ETHTOOL_GPAUSEPARAM 0x00000012 /* Get pause parameters */ |
| 1601 |
#define ETHTOOL_SPAUSEPARAM 0x00000013 /* Set pause parameters. */ |
| 1602 |
#define ETHTOOL_GRXCSUM 0x00000014 /* Get RX hw csum enable (ethtool_value) */ |
| 1603 |
#define ETHTOOL_SRXCSUM 0x00000015 /* Set RX hw csum enable (ethtool_value) */ |
| 1604 |
#define ETHTOOL_GTXCSUM 0x00000016 /* Get TX hw csum enable (ethtool_value) */ |
| 1605 |
#define ETHTOOL_STXCSUM 0x00000017 /* Set TX hw csum enable (ethtool_value) */ |
| 1606 |
#define ETHTOOL_GSG 0x00000018 /* Get scatter-gather enable |
| 1607 |
* (ethtool_value) */ |
| 1608 |
#define ETHTOOL_SSG 0x00000019 /* Set scatter-gather enable |
| 1609 |
* (ethtool_value). */ |
| 1610 |
#define ETHTOOL_TEST 0x0000001a /* execute NIC self-test. */ |
| 1611 |
#define ETHTOOL_GSTRINGS 0x0000001b /* get specified string set */ |
| 1612 |
#define ETHTOOL_PHYS_ID 0x0000001c /* identify the NIC */ |
| 1613 |
#define ETHTOOL_GSTATS 0x0000001d /* get NIC-specific statistics */ |
| 1614 |
#define ETHTOOL_GTSO 0x0000001e /* Get TSO enable (ethtool_value) */ |
| 1615 |
#define ETHTOOL_STSO 0x0000001f /* Set TSO enable (ethtool_value) */ |
| 1616 |
#define ETHTOOL_GPERMADDR 0x00000020 /* Get permanent hardware address */ |
| 1617 |
#define ETHTOOL_GUFO 0x00000021 /* Get UFO enable (ethtool_value) */ |
| 1618 |
#define ETHTOOL_SUFO 0x00000022 /* Set UFO enable (ethtool_value) */ |
| 1619 |
#define ETHTOOL_GGSO 0x00000023 /* Get GSO enable (ethtool_value) */ |
| 1620 |
#define ETHTOOL_SGSO 0x00000024 /* Set GSO enable (ethtool_value) */ |
| 1621 |
#define ETHTOOL_GFLAGS 0x00000025 /* Get flags bitmap(ethtool_value) */ |
| 1622 |
#define ETHTOOL_SFLAGS 0x00000026 /* Set flags bitmap(ethtool_value) */ |
| 1623 |
#define ETHTOOL_GPFLAGS 0x00000027 /* Get driver-private flags bitmap */ |
| 1624 |
#define ETHTOOL_SPFLAGS 0x00000028 /* Set driver-private flags bitmap */ |
| 1625 |
|
| 1626 |
#define ETHTOOL_GRXFH 0x00000029 /* Get RX flow hash configuration */ |
| 1627 |
#define ETHTOOL_SRXFH 0x0000002a /* Set RX flow hash configuration */ |
| 1628 |
#define ETHTOOL_GGRO 0x0000002b /* Get GRO enable (ethtool_value) */ |
| 1629 |
#define ETHTOOL_SGRO 0x0000002c /* Set GRO enable (ethtool_value) */ |
| 1630 |
#define ETHTOOL_GRXRINGS 0x0000002d /* Get RX rings available for LB */ |
| 1631 |
#define ETHTOOL_GRXCLSRLCNT 0x0000002e /* Get RX class rule count */ |
| 1632 |
#define ETHTOOL_GRXCLSRULE 0x0000002f /* Get RX classification rule */ |
| 1633 |
#define ETHTOOL_GRXCLSRLALL 0x00000030 /* Get all RX classification rule */ |
| 1634 |
#define ETHTOOL_SRXCLSRLDEL 0x00000031 /* Delete RX classification rule */ |
| 1635 |
#define ETHTOOL_SRXCLSRLINS 0x00000032 /* Insert RX classification rule */ |
| 1636 |
#define ETHTOOL_FLASHDEV 0x00000033 /* Flash firmware to device */ |
| 1637 |
#define ETHTOOL_RESET 0x00000034 /* Reset hardware */ |
| 1638 |
#define ETHTOOL_SRXNTUPLE 0x00000035 /* Add an n-tuple filter to device */ |
| 1639 |
#define ETHTOOL_GRXNTUPLE 0x00000036 /* deprecated */ |
| 1640 |
#define ETHTOOL_GSSET_INFO 0x00000037 /* Get string set info */ |
| 1641 |
#define ETHTOOL_GRXFHINDIR 0x00000038 /* Get RX flow hash indir'n table */ |
| 1642 |
#define ETHTOOL_SRXFHINDIR 0x00000039 /* Set RX flow hash indir'n table */ |
| 1643 |
|
| 1644 |
#define ETHTOOL_GFEATURES 0x0000003a /* Get device offload settings */ |
| 1645 |
#define ETHTOOL_SFEATURES 0x0000003b /* Change device offload settings */ |
| 1646 |
#define ETHTOOL_GCHANNELS 0x0000003c /* Get no of channels */ |
| 1647 |
#define ETHTOOL_SCHANNELS 0x0000003d /* Set no of channels */ |
| 1648 |
#define ETHTOOL_SET_DUMP 0x0000003e /* Set dump settings */ |
| 1649 |
#define ETHTOOL_GET_DUMP_FLAG 0x0000003f /* Get dump settings */ |
| 1650 |
#define ETHTOOL_GET_DUMP_DATA 0x00000040 /* Get dump data */ |
| 1651 |
#define ETHTOOL_GET_TS_INFO 0x00000041 /* Get time stamping and PHC info */ |
| 1652 |
#define ETHTOOL_GMODULEINFO 0x00000042 /* Get plug-in module information */ |
| 1653 |
#define ETHTOOL_GMODULEEEPROM 0x00000043 /* Get plug-in module eeprom */ |
| 1654 |
#define ETHTOOL_GEEE 0x00000044 /* Get EEE settings */ |
| 1655 |
#define ETHTOOL_SEEE 0x00000045 /* Set EEE settings */ |
| 1656 |
|
| 1657 |
#define ETHTOOL_GRSSH 0x00000046 /* Get RX flow hash configuration */ |
| 1658 |
#define ETHTOOL_SRSSH 0x00000047 /* Set RX flow hash configuration */ |
| 1659 |
#define ETHTOOL_GTUNABLE 0x00000048 /* Get tunable configuration */ |
| 1660 |
#define ETHTOOL_STUNABLE 0x00000049 /* Set tunable configuration */ |
| 1661 |
#define ETHTOOL_GPHYSTATS 0x0000004a /* get PHY-specific statistics */ |
| 1662 |
|
| 1663 |
#define ETHTOOL_PERQUEUE 0x0000004b /* Set per queue options */ |
| 1664 |
|
| 1665 |
#define ETHTOOL_GLINKSETTINGS 0x0000004c /* Get ethtool_link_settings */ |
| 1666 |
#define ETHTOOL_SLINKSETTINGS 0x0000004d /* Set ethtool_link_settings */ |
| 1667 |
#define ETHTOOL_PHY_GTUNABLE 0x0000004e /* Get PHY tunable configuration */ |
| 1668 |
#define ETHTOOL_PHY_STUNABLE 0x0000004f /* Set PHY tunable configuration */ |
| 1669 |
#define ETHTOOL_GFECPARAM 0x00000050 /* Get FEC settings */ |
| 1670 |
#define ETHTOOL_SFECPARAM 0x00000051 /* Set FEC settings */ |
| 1671 |
|
| 1672 |
/* compatibility with older code */ |
| 1673 |
#define SPARC_ETH_GSET ETHTOOL_GSET |
| 1674 |
#define SPARC_ETH_SSET ETHTOOL_SSET |
| 1675 |
|
| 1676 |
/* Link mode bit indices */ |
| 1677 |
enum ethtool_link_mode_bit_indices { |
| 1678 |
ETHTOOL_LINK_MODE_10baseT_Half_BIT = 0, |
| 1679 |
ETHTOOL_LINK_MODE_10baseT_Full_BIT = 1, |
| 1680 |
ETHTOOL_LINK_MODE_100baseT_Half_BIT = 2, |
| 1681 |
ETHTOOL_LINK_MODE_100baseT_Full_BIT = 3, |
| 1682 |
ETHTOOL_LINK_MODE_1000baseT_Half_BIT = 4, |
| 1683 |
ETHTOOL_LINK_MODE_1000baseT_Full_BIT = 5, |
| 1684 |
ETHTOOL_LINK_MODE_Autoneg_BIT = 6, |
| 1685 |
ETHTOOL_LINK_MODE_TP_BIT = 7, |
| 1686 |
ETHTOOL_LINK_MODE_AUI_BIT = 8, |
| 1687 |
ETHTOOL_LINK_MODE_MII_BIT = 9, |
| 1688 |
ETHTOOL_LINK_MODE_FIBRE_BIT = 10, |
| 1689 |
ETHTOOL_LINK_MODE_BNC_BIT = 11, |
| 1690 |
ETHTOOL_LINK_MODE_10000baseT_Full_BIT = 12, |
| 1691 |
ETHTOOL_LINK_MODE_Pause_BIT = 13, |
| 1692 |
ETHTOOL_LINK_MODE_Asym_Pause_BIT = 14, |
| 1693 |
ETHTOOL_LINK_MODE_2500baseX_Full_BIT = 15, |
| 1694 |
ETHTOOL_LINK_MODE_Backplane_BIT = 16, |
| 1695 |
ETHTOOL_LINK_MODE_1000baseKX_Full_BIT = 17, |
| 1696 |
ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT = 18, |
| 1697 |
ETHTOOL_LINK_MODE_10000baseKR_Full_BIT = 19, |
| 1698 |
ETHTOOL_LINK_MODE_10000baseR_FEC_BIT = 20, |
| 1699 |
ETHTOOL_LINK_MODE_20000baseMLD2_Full_BIT = 21, |
| 1700 |
ETHTOOL_LINK_MODE_20000baseKR2_Full_BIT = 22, |
| 1701 |
ETHTOOL_LINK_MODE_40000baseKR4_Full_BIT = 23, |
| 1702 |
ETHTOOL_LINK_MODE_40000baseCR4_Full_BIT = 24, |
| 1703 |
ETHTOOL_LINK_MODE_40000baseSR4_Full_BIT = 25, |
| 1704 |
ETHTOOL_LINK_MODE_40000baseLR4_Full_BIT = 26, |
| 1705 |
ETHTOOL_LINK_MODE_56000baseKR4_Full_BIT = 27, |
| 1706 |
ETHTOOL_LINK_MODE_56000baseCR4_Full_BIT = 28, |
| 1707 |
ETHTOOL_LINK_MODE_56000baseSR4_Full_BIT = 29, |
| 1708 |
ETHTOOL_LINK_MODE_56000baseLR4_Full_BIT = 30, |
| 1709 |
ETHTOOL_LINK_MODE_25000baseCR_Full_BIT = 31, |
| 1710 |
|
| 1711 |
/* Last allowed bit for __ETHTOOL_LINK_MODE_LEGACY_MASK is bit |
| 1712 |
* 31. Please do NOT define any SUPPORTED_* or ADVERTISED_* |
| 1713 |
* macro for bits > 31. The only way to use indices > 31 is to |
| 1714 |
* use the new ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. |
| 1715 |
*/ |
| 1716 |
|
| 1717 |
ETHTOOL_LINK_MODE_25000baseKR_Full_BIT = 32, |
| 1718 |
ETHTOOL_LINK_MODE_25000baseSR_Full_BIT = 33, |
| 1719 |
ETHTOOL_LINK_MODE_50000baseCR2_Full_BIT = 34, |
| 1720 |
ETHTOOL_LINK_MODE_50000baseKR2_Full_BIT = 35, |
| 1721 |
ETHTOOL_LINK_MODE_100000baseKR4_Full_BIT = 36, |
| 1722 |
ETHTOOL_LINK_MODE_100000baseSR4_Full_BIT = 37, |
| 1723 |
ETHTOOL_LINK_MODE_100000baseCR4_Full_BIT = 38, |
| 1724 |
ETHTOOL_LINK_MODE_100000baseLR4_ER4_Full_BIT = 39, |
| 1725 |
ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT = 40, |
| 1726 |
ETHTOOL_LINK_MODE_1000baseX_Full_BIT = 41, |
| 1727 |
ETHTOOL_LINK_MODE_10000baseCR_Full_BIT = 42, |
| 1728 |
ETHTOOL_LINK_MODE_10000baseSR_Full_BIT = 43, |
| 1729 |
ETHTOOL_LINK_MODE_10000baseLR_Full_BIT = 44, |
| 1730 |
ETHTOOL_LINK_MODE_10000baseLRM_Full_BIT = 45, |
| 1731 |
ETHTOOL_LINK_MODE_10000baseER_Full_BIT = 46, |
| 1732 |
ETHTOOL_LINK_MODE_2500baseT_Full_BIT = 47, |
| 1733 |
ETHTOOL_LINK_MODE_5000baseT_Full_BIT = 48, |
| 1734 |
|
| 1735 |
ETHTOOL_LINK_MODE_FEC_NONE_BIT = 49, |
| 1736 |
ETHTOOL_LINK_MODE_FEC_RS_BIT = 50, |
| 1737 |
ETHTOOL_LINK_MODE_FEC_BASER_BIT = 51, |
| 1738 |
ETHTOOL_LINK_MODE_50000baseKR_Full_BIT = 52, |
| 1739 |
ETHTOOL_LINK_MODE_50000baseSR_Full_BIT = 53, |
| 1740 |
ETHTOOL_LINK_MODE_50000baseCR_Full_BIT = 54, |
| 1741 |
ETHTOOL_LINK_MODE_50000baseLR_ER_FR_Full_BIT = 55, |
| 1742 |
ETHTOOL_LINK_MODE_50000baseDR_Full_BIT = 56, |
| 1743 |
ETHTOOL_LINK_MODE_100000baseKR2_Full_BIT = 57, |
| 1744 |
ETHTOOL_LINK_MODE_100000baseSR2_Full_BIT = 58, |
| 1745 |
ETHTOOL_LINK_MODE_100000baseCR2_Full_BIT = 59, |
| 1746 |
ETHTOOL_LINK_MODE_100000baseLR2_ER2_FR2_Full_BIT = 60, |
| 1747 |
ETHTOOL_LINK_MODE_100000baseDR2_Full_BIT = 61, |
| 1748 |
ETHTOOL_LINK_MODE_200000baseKR4_Full_BIT = 62, |
| 1749 |
ETHTOOL_LINK_MODE_200000baseSR4_Full_BIT = 63, |
| 1750 |
ETHTOOL_LINK_MODE_200000baseLR4_ER4_FR4_Full_BIT = 64, |
| 1751 |
ETHTOOL_LINK_MODE_200000baseDR4_Full_BIT = 65, |
| 1752 |
ETHTOOL_LINK_MODE_200000baseCR4_Full_BIT = 66, |
| 1753 |
ETHTOOL_LINK_MODE_100baseT1_Full_BIT = 67, |
| 1754 |
ETHTOOL_LINK_MODE_1000baseT1_Full_BIT = 68, |
| 1755 |
ETHTOOL_LINK_MODE_400000baseKR8_Full_BIT = 69, |
| 1756 |
ETHTOOL_LINK_MODE_400000baseSR8_Full_BIT = 70, |
| 1757 |
ETHTOOL_LINK_MODE_400000baseLR8_ER8_FR8_Full_BIT = 71, |
| 1758 |
ETHTOOL_LINK_MODE_400000baseDR8_Full_BIT = 72, |
| 1759 |
ETHTOOL_LINK_MODE_400000baseCR8_Full_BIT = 73, |
| 1760 |
ETHTOOL_LINK_MODE_FEC_LLRS_BIT = 74, |
| 1761 |
ETHTOOL_LINK_MODE_100000baseKR_Full_BIT = 75, |
| 1762 |
ETHTOOL_LINK_MODE_100000baseSR_Full_BIT = 76, |
| 1763 |
ETHTOOL_LINK_MODE_100000baseLR_ER_FR_Full_BIT = 77, |
| 1764 |
ETHTOOL_LINK_MODE_100000baseCR_Full_BIT = 78, |
| 1765 |
ETHTOOL_LINK_MODE_100000baseDR_Full_BIT = 79, |
| 1766 |
ETHTOOL_LINK_MODE_200000baseKR2_Full_BIT = 80, |
| 1767 |
ETHTOOL_LINK_MODE_200000baseSR2_Full_BIT = 81, |
| 1768 |
ETHTOOL_LINK_MODE_200000baseLR2_ER2_FR2_Full_BIT = 82, |
| 1769 |
ETHTOOL_LINK_MODE_200000baseDR2_Full_BIT = 83, |
| 1770 |
ETHTOOL_LINK_MODE_200000baseCR2_Full_BIT = 84, |
| 1771 |
ETHTOOL_LINK_MODE_400000baseKR4_Full_BIT = 85, |
| 1772 |
ETHTOOL_LINK_MODE_400000baseSR4_Full_BIT = 86, |
| 1773 |
ETHTOOL_LINK_MODE_400000baseLR4_ER4_FR4_Full_BIT = 87, |
| 1774 |
ETHTOOL_LINK_MODE_400000baseDR4_Full_BIT = 88, |
| 1775 |
ETHTOOL_LINK_MODE_400000baseCR4_Full_BIT = 89, |
| 1776 |
ETHTOOL_LINK_MODE_100baseFX_Half_BIT = 90, |
| 1777 |
ETHTOOL_LINK_MODE_100baseFX_Full_BIT = 91, |
| 1778 |
ETHTOOL_LINK_MODE_10baseT1L_Full_BIT = 92, |
| 1779 |
ETHTOOL_LINK_MODE_800000baseCR8_Full_BIT = 93, |
| 1780 |
ETHTOOL_LINK_MODE_800000baseKR8_Full_BIT = 94, |
| 1781 |
ETHTOOL_LINK_MODE_800000baseDR8_Full_BIT = 95, |
| 1782 |
ETHTOOL_LINK_MODE_800000baseDR8_2_Full_BIT = 96, |
| 1783 |
ETHTOOL_LINK_MODE_800000baseSR8_Full_BIT = 97, |
| 1784 |
ETHTOOL_LINK_MODE_800000baseVR8_Full_BIT = 98, |
| 1785 |
ETHTOOL_LINK_MODE_10baseT1S_Full_BIT = 99, |
| 1786 |
ETHTOOL_LINK_MODE_10baseT1S_Half_BIT = 100, |
| 1787 |
ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT = 101, |
| 1788 |
|
| 1789 |
/* must be last entry */ |
| 1790 |
__ETHTOOL_LINK_MODE_MASK_NBITS |
| 1791 |
}; |
| 1792 |
|
| 1793 |
#define __ETHTOOL_LINK_MODE_LEGACY_MASK(base_name) \ |
| 1794 |
(1UL << (ETHTOOL_LINK_MODE_ ## base_name ## _BIT)) |
| 1795 |
|
| 1796 |
/* DEPRECATED macros. Please migrate to |
| 1797 |
* ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. Please do NOT |
| 1798 |
* define any new SUPPORTED_* macro for bits > 31. |
| 1799 |
*/ |
| 1800 |
#define SUPPORTED_10baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Half) |
| 1801 |
#define SUPPORTED_10baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Full) |
| 1802 |
#define SUPPORTED_100baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Half) |
| 1803 |
#define SUPPORTED_100baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Full) |
| 1804 |
#define SUPPORTED_1000baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Half) |
| 1805 |
#define SUPPORTED_1000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Full) |
| 1806 |
#define SUPPORTED_Autoneg __ETHTOOL_LINK_MODE_LEGACY_MASK(Autoneg) |
| 1807 |
#define SUPPORTED_TP __ETHTOOL_LINK_MODE_LEGACY_MASK(TP) |
| 1808 |
#define SUPPORTED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI) |
| 1809 |
#define SUPPORTED_MII __ETHTOOL_LINK_MODE_LEGACY_MASK(MII) |
| 1810 |
#define SUPPORTED_FIBRE __ETHTOOL_LINK_MODE_LEGACY_MASK(FIBRE) |
| 1811 |
#define SUPPORTED_BNC __ETHTOOL_LINK_MODE_LEGACY_MASK(BNC) |
| 1812 |
#define SUPPORTED_10000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseT_Full) |
| 1813 |
#define SUPPORTED_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Pause) |
| 1814 |
#define SUPPORTED_Asym_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Asym_Pause) |
| 1815 |
#define SUPPORTED_2500baseX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(2500baseX_Full) |
| 1816 |
#define SUPPORTED_Backplane __ETHTOOL_LINK_MODE_LEGACY_MASK(Backplane) |
| 1817 |
#define SUPPORTED_1000baseKX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseKX_Full) |
| 1818 |
#define SUPPORTED_10000baseKX4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKX4_Full) |
| 1819 |
#define SUPPORTED_10000baseKR_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKR_Full) |
| 1820 |
#define SUPPORTED_10000baseR_FEC __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseR_FEC) |
| 1821 |
#define SUPPORTED_20000baseMLD2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseMLD2_Full) |
| 1822 |
#define SUPPORTED_20000baseKR2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseKR2_Full) |
| 1823 |
#define SUPPORTED_40000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseKR4_Full) |
| 1824 |
#define SUPPORTED_40000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseCR4_Full) |
| 1825 |
#define SUPPORTED_40000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseSR4_Full) |
| 1826 |
#define SUPPORTED_40000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseLR4_Full) |
| 1827 |
#define SUPPORTED_56000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseKR4_Full) |
| 1828 |
#define SUPPORTED_56000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseCR4_Full) |
| 1829 |
#define SUPPORTED_56000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseSR4_Full) |
| 1830 |
#define SUPPORTED_56000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseLR4_Full) |
| 1831 |
/* Please do not define any new SUPPORTED_* macro for bits > 31, see |
| 1832 |
* notice above. |
| 1833 |
*/ |
| 1834 |
|
| 1835 |
/* |
| 1836 |
* DEPRECATED macros. Please migrate to |
| 1837 |
* ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. Please do NOT |
| 1838 |
* define any new ADERTISE_* macro for bits > 31. |
| 1839 |
*/ |
| 1840 |
#define ADVERTISED_10baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Half) |
| 1841 |
#define ADVERTISED_10baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Full) |
| 1842 |
#define ADVERTISED_100baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Half) |
| 1843 |
#define ADVERTISED_100baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Full) |
| 1844 |
#define ADVERTISED_1000baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Half) |
| 1845 |
#define ADVERTISED_1000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Full) |
| 1846 |
#define ADVERTISED_Autoneg __ETHTOOL_LINK_MODE_LEGACY_MASK(Autoneg) |
| 1847 |
#define ADVERTISED_TP __ETHTOOL_LINK_MODE_LEGACY_MASK(TP) |
| 1848 |
#define ADVERTISED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI) |
| 1849 |
#define ADVERTISED_MII __ETHTOOL_LINK_MODE_LEGACY_MASK(MII) |
| 1850 |
#define ADVERTISED_FIBRE __ETHTOOL_LINK_MODE_LEGACY_MASK(FIBRE) |
| 1851 |
#define ADVERTISED_BNC __ETHTOOL_LINK_MODE_LEGACY_MASK(BNC) |
| 1852 |
#define ADVERTISED_10000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseT_Full) |
| 1853 |
#define ADVERTISED_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Pause) |
| 1854 |
#define ADVERTISED_Asym_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Asym_Pause) |
| 1855 |
#define ADVERTISED_2500baseX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(2500baseX_Full) |
| 1856 |
#define ADVERTISED_Backplane __ETHTOOL_LINK_MODE_LEGACY_MASK(Backplane) |
| 1857 |
#define ADVERTISED_1000baseKX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseKX_Full) |
| 1858 |
#define ADVERTISED_10000baseKX4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKX4_Full) |
| 1859 |
#define ADVERTISED_10000baseKR_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKR_Full) |
| 1860 |
#define ADVERTISED_10000baseR_FEC __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseR_FEC) |
| 1861 |
#define ADVERTISED_20000baseMLD2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseMLD2_Full) |
| 1862 |
#define ADVERTISED_20000baseKR2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseKR2_Full) |
| 1863 |
#define ADVERTISED_40000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseKR4_Full) |
| 1864 |
#define ADVERTISED_40000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseCR4_Full) |
| 1865 |
#define ADVERTISED_40000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseSR4_Full) |
| 1866 |
#define ADVERTISED_40000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseLR4_Full) |
| 1867 |
#define ADVERTISED_56000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseKR4_Full) |
| 1868 |
#define ADVERTISED_56000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseCR4_Full) |
| 1869 |
#define ADVERTISED_56000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseSR4_Full) |
| 1870 |
#define ADVERTISED_56000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseLR4_Full) |
| 1871 |
/* Please do not define any new ADVERTISED_* macro for bits > 31, see |
| 1872 |
* notice above. |
| 1873 |
*/ |
| 1874 |
|
| 1875 |
/* The following are all involved in forcing a particular link |
| 1876 |
* mode for the device for setting things. When getting the |
| 1877 |
* devices settings, these indicate the current mode and whether |
| 1878 |
* it was forced up into this mode or autonegotiated. |
| 1879 |
*/ |
| 1880 |
|
| 1881 |
/* The forced speed, in units of 1Mb. All values 0 to INT_MAX are legal. |
| 1882 |
* Update drivers/net/phy/phy.c:phy_speed_to_str() and |
| 1883 |
* drivers/net/bonding/bond_3ad.c:__get_link_speed() when adding new values. |
| 1884 |
*/ |
| 1885 |
#define SPEED_10 10 |
| 1886 |
#define SPEED_100 100 |
| 1887 |
#define SPEED_1000 1000 |
| 1888 |
#define SPEED_2500 2500 |
| 1889 |
#define SPEED_5000 5000 |
| 1890 |
#define SPEED_10000 10000 |
| 1891 |
#define SPEED_14000 14000 |
| 1892 |
#define SPEED_20000 20000 |
| 1893 |
#define SPEED_25000 25000 |
| 1894 |
#define SPEED_40000 40000 |
| 1895 |
#define SPEED_50000 50000 |
| 1896 |
#define SPEED_56000 56000 |
| 1897 |
#define SPEED_100000 100000 |
| 1898 |
#define SPEED_200000 200000 |
| 1899 |
#define SPEED_400000 400000 |
| 1900 |
#define SPEED_800000 800000 |
| 1901 |
|
| 1902 |
#define SPEED_UNKNOWN -1 |
| 1903 |
|
| 1904 |
static __inline__ int ethtool_validate_speed(__u32 speed) |
| 1905 |
{ |
| 1906 |
return speed <= INT_MAX || speed == (__u32)SPEED_UNKNOWN; |
| 1907 |
} |
| 1908 |
|
| 1909 |
/* Duplex, half or full. */ |
| 1910 |
#define DUPLEX_HALF 0x00 |
| 1911 |
#define DUPLEX_FULL 0x01 |
| 1912 |
#define DUPLEX_UNKNOWN 0xff |
| 1913 |
|
| 1914 |
static __inline__ int ethtool_validate_duplex(__u8 duplex) |
| 1915 |
{ |
| 1916 |
switch (duplex) { |
| 1917 |
case DUPLEX_HALF: |
| 1918 |
case DUPLEX_FULL: |
| 1919 |
case DUPLEX_UNKNOWN: |
| 1920 |
return 1; |
| 1921 |
} |
| 1922 |
|
| 1923 |
return 0; |
| 1924 |
} |
| 1925 |
|
| 1926 |
#define MASTER_SLAVE_CFG_UNSUPPORTED 0 |
| 1927 |
#define MASTER_SLAVE_CFG_UNKNOWN 1 |
| 1928 |
#define MASTER_SLAVE_CFG_MASTER_PREFERRED 2 |
| 1929 |
#define MASTER_SLAVE_CFG_SLAVE_PREFERRED 3 |
| 1930 |
#define MASTER_SLAVE_CFG_MASTER_FORCE 4 |
| 1931 |
#define MASTER_SLAVE_CFG_SLAVE_FORCE 5 |
| 1932 |
#define MASTER_SLAVE_STATE_UNSUPPORTED 0 |
| 1933 |
#define MASTER_SLAVE_STATE_UNKNOWN 1 |
| 1934 |
#define MASTER_SLAVE_STATE_MASTER 2 |
| 1935 |
#define MASTER_SLAVE_STATE_SLAVE 3 |
| 1936 |
#define MASTER_SLAVE_STATE_ERR 4 |
| 1937 |
|
| 1938 |
/* These are used to throttle the rate of data on the phy interface when the |
| 1939 |
* native speed of the interface is higher than the link speed. These should |
| 1940 |
* not be used for phy interfaces which natively support multiple speeds (e.g. |
| 1941 |
* MII or SGMII). |
| 1942 |
*/ |
| 1943 |
/* No rate matching performed. */ |
| 1944 |
#define RATE_MATCH_NONE 0 |
| 1945 |
/* The phy sends pause frames to throttle the MAC. */ |
| 1946 |
#define RATE_MATCH_PAUSE 1 |
| 1947 |
/* The phy asserts CRS to prevent the MAC from transmitting. */ |
| 1948 |
#define RATE_MATCH_CRS 2 |
| 1949 |
/* The MAC is programmed with a sufficiently-large IPG. */ |
| 1950 |
#define RATE_MATCH_OPEN_LOOP 3 |
| 1951 |
|
| 1952 |
/* Which connector port. */ |
| 1953 |
#define PORT_TP 0x00 |
| 1954 |
#define PORT_AUI 0x01 |
| 1955 |
#define PORT_MII 0x02 |
| 1956 |
#define PORT_FIBRE 0x03 |
| 1957 |
#define PORT_BNC 0x04 |
| 1958 |
#define PORT_DA 0x05 |
| 1959 |
#define PORT_NONE 0xef |
| 1960 |
#define PORT_OTHER 0xff |
| 1961 |
|
| 1962 |
/* Which transceiver to use. */ |
| 1963 |
#define XCVR_INTERNAL 0x00 /* PHY and MAC are in the same package */ |
| 1964 |
#define XCVR_EXTERNAL 0x01 /* PHY and MAC are in different packages */ |
| 1965 |
#define XCVR_DUMMY1 0x02 |
| 1966 |
#define XCVR_DUMMY2 0x03 |
| 1967 |
#define XCVR_DUMMY3 0x04 |
| 1968 |
|
| 1969 |
/* Enable or disable autonegotiation. */ |
| 1970 |
#define AUTONEG_DISABLE 0x00 |
| 1971 |
#define AUTONEG_ENABLE 0x01 |
| 1972 |
|
| 1973 |
/* MDI or MDI-X status/control - if MDI/MDI_X/AUTO is set then |
| 1974 |
* the driver is required to renegotiate link |
| 1975 |
*/ |
| 1976 |
#define ETH_TP_MDI_INVALID 0x00 /* status: unknown; control: unsupported */ |
| 1977 |
#define ETH_TP_MDI 0x01 /* status: MDI; control: force MDI */ |
| 1978 |
#define ETH_TP_MDI_X 0x02 /* status: MDI-X; control: force MDI-X */ |
| 1979 |
#define ETH_TP_MDI_AUTO 0x03 /* control: auto-select */ |
| 1980 |
|
| 1981 |
/* Wake-On-Lan options. */ |
| 1982 |
#define WAKE_PHY (1 << 0) |
| 1983 |
#define WAKE_UCAST (1 << 1) |
| 1984 |
#define WAKE_MCAST (1 << 2) |
| 1985 |
#define WAKE_BCAST (1 << 3) |
| 1986 |
#define WAKE_ARP (1 << 4) |
| 1987 |
#define WAKE_MAGIC (1 << 5) |
| 1988 |
#define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */ |
| 1989 |
#define WAKE_FILTER (1 << 7) |
| 1990 |
|
| 1991 |
#define WOL_MODE_COUNT 8 |
| 1992 |
|
| 1993 |
/* L2-L4 network traffic flow types */ |
| 1994 |
#define TCP_V4_FLOW 0x01 /* hash or spec (tcp_ip4_spec) */ |
| 1995 |
#define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */ |
| 1996 |
#define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */ |
| 1997 |
#define AH_ESP_V4_FLOW 0x04 /* hash only */ |
| 1998 |
#define TCP_V6_FLOW 0x05 /* hash or spec (tcp_ip6_spec; nfc only) */ |
| 1999 |
#define UDP_V6_FLOW 0x06 /* hash or spec (udp_ip6_spec; nfc only) */ |
| 2000 |
#define SCTP_V6_FLOW 0x07 /* hash or spec (sctp_ip6_spec; nfc only) */ |
| 2001 |
#define AH_ESP_V6_FLOW 0x08 /* hash only */ |
| 2002 |
#define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */ |
| 2003 |
#define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */ |
| 2004 |
#define AH_V6_FLOW 0x0b /* hash or spec (ah_ip6_spec; nfc only) */ |
| 2005 |
#define ESP_V6_FLOW 0x0c /* hash or spec (esp_ip6_spec; nfc only) */ |
| 2006 |
#define IPV4_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */ |
| 2007 |
#define IP_USER_FLOW IPV4_USER_FLOW |
| 2008 |
#define IPV6_USER_FLOW 0x0e /* spec only (usr_ip6_spec; nfc only) */ |
| 2009 |
#define IPV4_FLOW 0x10 /* hash only */ |
| 2010 |
#define IPV6_FLOW 0x11 /* hash only */ |
| 2011 |
#define ETHER_FLOW 0x12 /* spec only (ether_spec) */ |
| 2012 |
/* Flag to enable additional fields in struct ethtool_rx_flow_spec */ |
| 2013 |
#define FLOW_EXT 0x80000000 |
| 2014 |
#define FLOW_MAC_EXT 0x40000000 |
| 2015 |
/* Flag to enable RSS spreading of traffic matching rule (nfc only) */ |
| 2016 |
#define FLOW_RSS 0x20000000 |
| 2017 |
|
| 2018 |
/* L3-L4 network traffic flow hash options */ |
| 2019 |
#define RXH_L2DA (1 << 1) |
| 2020 |
#define RXH_VLAN (1 << 2) |
| 2021 |
#define RXH_L3_PROTO (1 << 3) |
| 2022 |
#define RXH_IP_SRC (1 << 4) |
| 2023 |
#define RXH_IP_DST (1 << 5) |
| 2024 |
#define RXH_L4_B_0_1 (1 << 6) /* src port in case of TCP/UDP/SCTP */ |
| 2025 |
#define RXH_L4_B_2_3 (1 << 7) /* dst port in case of TCP/UDP/SCTP */ |
| 2026 |
#define RXH_DISCARD (1 << 31) |
| 2027 |
|
| 2028 |
#define RX_CLS_FLOW_DISC 0xffffffffffffffffULL |
| 2029 |
#define RX_CLS_FLOW_WAKE 0xfffffffffffffffeULL |
| 2030 |
|
| 2031 |
/* Special RX classification rule insert location values */ |
| 2032 |
#define RX_CLS_LOC_SPECIAL 0x80000000 /* flag */ |
| 2033 |
#define RX_CLS_LOC_ANY 0xffffffff |
| 2034 |
#define RX_CLS_LOC_FIRST 0xfffffffe |
| 2035 |
#define RX_CLS_LOC_LAST 0xfffffffd |
| 2036 |
|
| 2037 |
/* EEPROM Standards for plug in modules */ |
| 2038 |
#define ETH_MODULE_SFF_8079 0x1 |
| 2039 |
#define ETH_MODULE_SFF_8079_LEN 256 |
| 2040 |
#define ETH_MODULE_SFF_8472 0x2 |
| 2041 |
#define ETH_MODULE_SFF_8472_LEN 512 |
| 2042 |
#define ETH_MODULE_SFF_8636 0x3 |
| 2043 |
#define ETH_MODULE_SFF_8636_LEN 256 |
| 2044 |
#define ETH_MODULE_SFF_8436 0x4 |
| 2045 |
#define ETH_MODULE_SFF_8436_LEN 256 |
| 2046 |
|
| 2047 |
#define ETH_MODULE_SFF_8636_MAX_LEN 640 |
| 2048 |
#define ETH_MODULE_SFF_8436_MAX_LEN 640 |
| 2049 |
|
| 2050 |
/* Reset flags */ |
| 2051 |
/* The reset() operation must clear the flags for the components which |
| 2052 |
* were actually reset. On successful return, the flags indicate the |
| 2053 |
* components which were not reset, either because they do not exist |
| 2054 |
* in the hardware or because they cannot be reset independently. The |
| 2055 |
* driver must never reset any components that were not requested. |
| 2056 |
*/ |
| 2057 |
enum ethtool_reset_flags { |
| 2058 |
/* These flags represent components dedicated to the interface |
| 2059 |
* the command is addressed to. Shift any flag left by |
| 2060 |
* ETH_RESET_SHARED_SHIFT to reset a shared component of the |
| 2061 |
* same type. |
| 2062 |
*/ |
| 2063 |
ETH_RESET_MGMT = 1 << 0, /* Management processor */ |
| 2064 |
ETH_RESET_IRQ = 1 << 1, /* Interrupt requester */ |
| 2065 |
ETH_RESET_DMA = 1 << 2, /* DMA engine */ |
| 2066 |
ETH_RESET_FILTER = 1 << 3, /* Filtering/flow direction */ |
| 2067 |
ETH_RESET_OFFLOAD = 1 << 4, /* Protocol offload */ |
| 2068 |
ETH_RESET_MAC = 1 << 5, /* Media access controller */ |
| 2069 |
ETH_RESET_PHY = 1 << 6, /* Transceiver/PHY */ |
| 2070 |
ETH_RESET_RAM = 1 << 7, /* RAM shared between |
| 2071 |
* multiple components */ |
| 2072 |
ETH_RESET_AP = 1 << 8, /* Application processor */ |
| 2073 |
|
| 2074 |
ETH_RESET_DEDICATED = 0x0000ffff, /* All components dedicated to |
| 2075 |
* this interface */ |
| 2076 |
ETH_RESET_ALL = 0xffffffff, /* All components used by this |
| 2077 |
* interface, even if shared */ |
| 2078 |
}; |
| 2079 |
#define ETH_RESET_SHARED_SHIFT 16 |
| 2080 |
|
| 2081 |
|
| 2082 |
/** |
| 2083 |
* struct ethtool_link_settings - link control and status |
| 2084 |
* |
| 2085 |
* IMPORTANT, Backward compatibility notice: When implementing new |
| 2086 |
* user-space tools, please first try %ETHTOOL_GLINKSETTINGS, and |
| 2087 |
* if it succeeds use %ETHTOOL_SLINKSETTINGS to change link |
| 2088 |
* settings; do not use %ETHTOOL_SSET if %ETHTOOL_GLINKSETTINGS |
| 2089 |
* succeeded: stick to %ETHTOOL_GLINKSETTINGS/%SLINKSETTINGS in |
| 2090 |
* that case. Conversely, if %ETHTOOL_GLINKSETTINGS fails, use |
| 2091 |
* %ETHTOOL_GSET to query and %ETHTOOL_SSET to change link |
| 2092 |
* settings; do not use %ETHTOOL_SLINKSETTINGS if |
| 2093 |
* %ETHTOOL_GLINKSETTINGS failed: stick to |
| 2094 |
* %ETHTOOL_GSET/%ETHTOOL_SSET in that case. |
| 2095 |
* |
| 2096 |
* @cmd: Command number = %ETHTOOL_GLINKSETTINGS or %ETHTOOL_SLINKSETTINGS |
| 2097 |
* @speed: Link speed (Mbps) |
| 2098 |
* @duplex: Duplex mode; one of %DUPLEX_* |
| 2099 |
* @port: Physical connector type; one of %PORT_* |
| 2100 |
* @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not |
| 2101 |
* applicable. For clause 45 PHYs this is the PRTAD. |
| 2102 |
* @autoneg: Enable/disable autonegotiation and auto-detection; |
| 2103 |
* either %AUTONEG_DISABLE or %AUTONEG_ENABLE |
| 2104 |
* @mdio_support: Bitmask of %ETH_MDIO_SUPPORTS_* flags for the MDIO |
| 2105 |
* protocols supported by the interface; 0 if unknown. |
| 2106 |
* Read-only. |
| 2107 |
* @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of |
| 2108 |
* %ETH_TP_MDI_*. If the status is unknown or not applicable, the |
| 2109 |
* value will be %ETH_TP_MDI_INVALID. Read-only. |
| 2110 |
* @eth_tp_mdix_ctrl: Ethernet twisted pair MDI(-X) control; one of |
| 2111 |
* %ETH_TP_MDI_*. If MDI(-X) control is not implemented, reads |
| 2112 |
* yield %ETH_TP_MDI_INVALID and writes may be ignored or rejected. |
| 2113 |
* When written successfully, the link should be renegotiated if |
| 2114 |
* necessary. |
| 2115 |
* @link_mode_masks_nwords: Number of 32-bit words for each of the |
| 2116 |
* supported, advertising, lp_advertising link mode bitmaps. For |
| 2117 |
* %ETHTOOL_GLINKSETTINGS: on entry, number of words passed by user |
| 2118 |
* (>= 0); on return, if handshake in progress, negative if |
| 2119 |
* request size unsupported by kernel: absolute value indicates |
| 2120 |
* kernel expected size and all the other fields but cmd |
| 2121 |
* are 0; otherwise (handshake completed), strictly positive |
| 2122 |
* to indicate size used by kernel and cmd field stays |
| 2123 |
* %ETHTOOL_GLINKSETTINGS, all other fields populated by driver. For |
| 2124 |
* %ETHTOOL_SLINKSETTINGS: must be valid on entry, ie. a positive |
| 2125 |
* value returned previously by %ETHTOOL_GLINKSETTINGS, otherwise |
| 2126 |
* refused. For drivers: ignore this field (use kernel's |
| 2127 |
* __ETHTOOL_LINK_MODE_MASK_NBITS instead), any change to it will |
| 2128 |
* be overwritten by kernel. |
| 2129 |
* @supported: Bitmap with each bit meaning given by |
| 2130 |
* %ethtool_link_mode_bit_indices for the link modes, physical |
| 2131 |
* connectors and other link features for which the interface |
| 2132 |
* supports autonegotiation or auto-detection. Read-only. |
| 2133 |
* @advertising: Bitmap with each bit meaning given by |
| 2134 |
* %ethtool_link_mode_bit_indices for the link modes, physical |
| 2135 |
* connectors and other link features that are advertised through |
| 2136 |
* autonegotiation or enabled for auto-detection. |
| 2137 |
* @lp_advertising: Bitmap with each bit meaning given by |
| 2138 |
* %ethtool_link_mode_bit_indices for the link modes, and other |
| 2139 |
* link features that the link partner advertised through |
| 2140 |
* autonegotiation; 0 if unknown or not applicable. Read-only. |
| 2141 |
* @transceiver: Used to distinguish different possible PHY types, |
| 2142 |
* reported consistently by PHYLIB. Read-only. |
| 2143 |
* @master_slave_cfg: Master/slave port mode. |
| 2144 |
* @master_slave_state: Master/slave port state. |
| 2145 |
* @rate_matching: Rate adaptation performed by the PHY |
| 2146 |
* @reserved: Reserved for future use; see the note on reserved space. |
| 2147 |
* @link_mode_masks: Variable length bitmaps. |
| 2148 |
* |
| 2149 |
* If autonegotiation is disabled, the speed and @duplex represent the |
| 2150 |
* fixed link mode and are writable if the driver supports multiple |
| 2151 |
* link modes. If it is enabled then they are read-only; if the link |
| 2152 |
* is up they represent the negotiated link mode; if the link is down, |
| 2153 |
* the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and |
| 2154 |
* @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode. |
| 2155 |
* |
| 2156 |
* Some hardware interfaces may have multiple PHYs and/or physical |
| 2157 |
* connectors fitted or do not allow the driver to detect which are |
| 2158 |
* fitted. For these interfaces @port and/or @phy_address may be |
| 2159 |
* writable, possibly dependent on @autoneg being %AUTONEG_DISABLE. |
| 2160 |
* Otherwise, attempts to write different values may be ignored or |
| 2161 |
* rejected. |
| 2162 |
* |
| 2163 |
* Deprecated %ethtool_cmd fields transceiver, maxtxpkt and maxrxpkt |
| 2164 |
* are not available in %ethtool_link_settings. These fields will be |
| 2165 |
* always set to zero in %ETHTOOL_GSET reply and %ETHTOOL_SSET will |
| 2166 |
* fail if any of them is set to non-zero value. |
| 2167 |
* |
| 2168 |
* Users should assume that all fields not marked read-only are |
| 2169 |
* writable and subject to validation by the driver. They should use |
| 2170 |
* %ETHTOOL_GLINKSETTINGS to get the current values before making specific |
| 2171 |
* changes and then applying them with %ETHTOOL_SLINKSETTINGS. |
| 2172 |
* |
| 2173 |
* Drivers that implement %get_link_ksettings and/or |
| 2174 |
* %set_link_ksettings should ignore the @cmd |
| 2175 |
* and @link_mode_masks_nwords fields (any change to them overwritten |
| 2176 |
* by kernel), and rely only on kernel's internal |
| 2177 |
* %__ETHTOOL_LINK_MODE_MASK_NBITS and |
| 2178 |
* %ethtool_link_mode_mask_t. Drivers that implement |
| 2179 |
* %set_link_ksettings() should validate all fields other than @cmd |
| 2180 |
* and @link_mode_masks_nwords that are not described as read-only or |
| 2181 |
* deprecated, and must ignore all fields described as read-only. |
| 2182 |
*/ |
| 2183 |
struct ethtool_link_settings { |
| 2184 |
__u32 cmd; |
| 2185 |
__u32 speed; |
| 2186 |
__u8 duplex; |
| 2187 |
__u8 port; |
| 2188 |
__u8 phy_address; |
| 2189 |
__u8 autoneg; |
| 2190 |
__u8 mdio_support; |
| 2191 |
__u8 eth_tp_mdix; |
| 2192 |
__u8 eth_tp_mdix_ctrl; |
| 2193 |
__s8 link_mode_masks_nwords; |
| 2194 |
__u8 transceiver; |
| 2195 |
__u8 master_slave_cfg; |
| 2196 |
__u8 master_slave_state; |
| 2197 |
__u8 rate_matching; |
| 2198 |
__u32 reserved[7]; |
| 2199 |
__u32 link_mode_masks[]; |
| 2200 |
/* layout of link_mode_masks fields: |
| 2201 |
* __u32 map_supported[link_mode_masks_nwords]; |
| 2202 |
* __u32 map_advertising[link_mode_masks_nwords]; |
| 2203 |
* __u32 map_lp_advertising[link_mode_masks_nwords]; |
| 2204 |
*/ |
| 2205 |
}; |
| 2206 |
#endif /* _LINUX_ETHTOOL_H */ |