Debian Codegraph @

README.md

raw
1 # Exos II GoTo Telescope Mount Driver for libindi
2
3 ---
4
5 ## Disclaimer
6 You get the driver free of charge and, also may modify it to your needs.
7
8 However the software is distributed AS IS.
9
10 **I'M NOT RESPONSIBLE FOR ANY DAMAGES OR INJURIES, CAUSED BY THIS SOFTWARE!**
11
12 ---
13
14 ## Features of the Driver
15 - Works with KStars/Stellarium using Indi Connection
16 - GoTo Coordinates and Track commands (Sidereal Tracking only)
17 - Park and Abort commands
18 - Sync command for alignment of Software Sky and actual pointing
19 - Get/Set Site Location
20 - Set Date/Time
21 - Adjust Pointing while Tracking
22
23
24 **Note:** *To Avoid you the trouble of building this driver yourself, Version 0.900 is now integrated in the indi 3rd party driver package, and should be distributed alongside commercial devices. Driver updates will be pushed upstream when relevant changes are implemented!*
25
26 ---
27
28 ## Introduction
29 This is a basic driver for the Bresser Exos II GoTo telescope mount controller, allowing the connection to Indi clients/software.
30 The driver is intended for remote control on a Raspberry Pi, running Astroberry with libindi, but may run on any Indi running platform.
31 Its current state is experimental, but hopefully gradually improves.
32 Since its the initial release, feedback for improvement is appreciated.
33
34 If your have an improvements, features to add or a bug to report, please fell free to write a mail, a ticket in the issues section or a pull request.
35
36 ### About the Mount
37 The Bresser Exos II GoTo Mount has a relabled JOC SkyViewer Handbox (PCB Rev. 1.09 2012_08), there are several other versions handbox revisions out there.
38 It runs the Firmware Version 2.3 distributed by Bresser.
39 The mount is quite autonomous, in terms motion controls, when initialized properly no jams or crashes where noticed.
40 On the serial protocol side however, this device is quite primitive.
41 The data exchange is established using a 13 Byte message frame, with a 4 Byte preamble, leaving 1 byte for a command and 8 bytes for command parameter data.
42 The protocol only accepts, a few commands for goto, sync, parking, motion stop and Location/Time/Date setting.
43 The Device is not very talkative, it only sends responses to location command, and only reports back the its current pointing coordinates, without the tracking status information.
44 This makes it difficult to determine the state of the mount.
45 Also this introduces some limitations which competative products may not have.
46
47 The serial protocol was reverse engineered using serial port sniffing tools, developping this driver as a result.
48
49 ---
50
51 ## Requirements
52 ***This driver is intended for Bresser Exos II GoTo System not the Explore Scientific Exos II which may share some similiarities. The drivers for these system and its derivitives are already included in the INDI Environment.***
53
54 - Raspberry Pi with Astroberry (AB, Version 2.0.3 or higher) with Libindi 1.8.7 or higher (https://www.astroberry.io/, https://www.indilib.org/), In fact: any platform running indi will do.
55 - latest Version of cmake installed (at least Version 3.00)
56 - latest git version installed
57 - Astronomy Software (KStars, for Windows download see: https://edu.kde.org/kstars/#download, or use the package manager of your linux distribution)
58 - A COM Port or working USB to Serial Adapter (any device supporting the change of Baud Rates will do!)
59 - The Bresser Serial Adapter for the Handbox (https://www.bresser.de/Astronomie/Zubehoer/Motoren-Steuerungen/BRESSER-Computer-Kabel-zur-Fernsteuerung-von-MCX-Goto-Teleskopen-und-EXOS-II-EQ-Goto-Montierungen.html)
60 - The Bresser Exos II GoTo Mount (or the Upgrade Kit) (https://www.bresser.de/Astronomie/BRESSER-Messier-EXOS-2-EQ-GoTo-Montierung.html, https://www.bresser.de/Astronomie/Zubehoer/Motoren-Steuerungen/BRESSER-StarTracker-GoTo-Kit.html)
61 - The EQ mount AZ/ALT version is not supported!
62 - Firmware Version 2.3 installed on the Handbox (https://www.bresser.de/Astronomie/Zubehoer/Motoren-Steuerungen/BRESSER-Computer-Kabel-zur-Fernsteuerung-von-MCX-Goto-Teleskopen-und-EXOS-II-EQ-Goto-Montierungen.html, under Manual)
63
64 ## Known Issues and Limitations
65 - Tracking modes can not be set, only Sidereal Tracking is working right now.
66 - More a Hint than an issue: Sync only works when tracking an object. This behaviour is implemented on the handbox and can not be changed.
67 - The sync function only works if you changed the pointing with your hand box not via the EKOS pointing control
68 - you can not perform the meridian flip from afar, since the handbox does not allow it.
69 - Software Sky Coordinates may differ from Handbox Coordinates
70
71 ---
72
73 ## Getting started
74
75 - See [Driver installation](Documentation/Installation.md) for installing the driver.
76 - See [Application setup](Documentation/ApplicationSetup.md) how to setup the driver in observatory software.
77 - See [Troubleshooting](Documentation/Troubleshooting.md) for advice on how to resolve common issues.
78 - See [FAQ](Documentation/FAQ.md) for common questions.
79 - See [Schematics](Documentation/Schematics/Schematics.md) and overview of the electronics of the system.
80 ---
81
82 ## Important Note before Further Setup or Observation
83 It is **important** that you put the scope in the Home position, Polar and Star Align in accordance to the Bresser manual provided with the telescope and mount.
84
85 **Its vital in order to avoid damage to your Equipment. This Driver can not handle this for your!**
86
87 **Also do not point your Telescope directly to the sun, without recommended protective equipment, using this driver. It only handles coordinates not objects, and will therefore no prevent you from looking directly in to the sun!**
88
89 ---
90
91 ## Thanks
92 - Thanks to spitzbube for his effort in reverse engineering the handbox (https://github.com/Spitzbube/EXOS-2_GoTo_HandController) for revealing valuable insights!
93 - Thanks to SimonLilie from https://forum.astronomie.de for feedback and testing!