| 1 |
# |
| 2 |
# Copyright 2024 Centreon (http://www.centreon.com/) |
| 3 |
# |
| 4 |
# Centreon is a full-fledged industry-strength solution that meets |
| 5 |
# the needs in IT infrastructure and application monitoring for |
| 6 |
# service performance. |
| 7 |
# |
| 8 |
# Licensed under the Apache License, Version 2.0 (the "License"); |
| 9 |
# you may not use this file except in compliance with the License. |
| 10 |
# You may obtain a copy of the License at |
| 11 |
# |
| 12 |
# http://www.apache.org/licenses/LICENSE-2.0 |
| 13 |
# |
| 14 |
# Unless required by applicable law or agreed to in writing, software |
| 15 |
# distributed under the License is distributed on an "AS IS" BASIS, |
| 16 |
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| 17 |
# See the License for the specific language governing permissions and |
| 18 |
# limitations under the License. |
| 19 |
# |
| 20 |
|
| 21 |
package storage::emc::celerra::local::mode::getreason; |
| 22 |
|
| 23 |
use base qw(centreon::plugins::templates::hardware); |
| 24 |
|
| 25 |
use strict; |
| 26 |
use warnings; |
| 27 |
|
| 28 |
sub set_system { |
| 29 |
my ($self, %options) = @_; |
| 30 |
|
| 31 |
$self->{cb_hook2} = 'cmd_execute'; |
| 32 |
|
| 33 |
$self->{thresholds} = { |
| 34 |
controlstation => [ |
| 35 |
['Primary Control Station', 'OK'], # 10 |
| 36 |
['Secondary Control Station', 'OK'], # 11 |
| 37 |
['Control Station is ready, but is not running NAS service', 'CRITICAL'] # 6 |
| 38 |
], |
| 39 |
datamover => [ |
| 40 |
['Reset (or unknown state)', 'WARNING'], |
| 41 |
['DOS boot phase, BIOS check, boot sequence', 'WARNING'], |
| 42 |
['SIB POST failures (that is, hardware failures)', 'CRITICAL'], |
| 43 |
['DART is loaded on Data Mover, DOS boot and execution of boot.bat, boot.cfg', 'WARNING'], |
| 44 |
['DART is ready on Data Mover, running, and MAC threads started', 'WARNING'], |
| 45 |
['DART is in contact with Control Station box monitor', 'OK'], |
| 46 |
['DART is in panic state', 'CRITICAL'], |
| 47 |
['DART reboot is pending or in halted state', 'WARNING'], |
| 48 |
['DART panicked and completed memory dump', 'CRITICAL'], |
| 49 |
['DM Misc problems', 'CRITICAL'], # code 14 |
| 50 |
['Data Mover is flashing firmware. DART is flashing BIOS and/or POST firmware. Data Mover cannot be reset', 'CRITICAL'], |
| 51 |
['Data Mover Hardware fault detected', 'CRITICAL'], |
| 52 |
['DM Memory Test Failure. BIOS detected memory error', 'CRITICAL'], |
| 53 |
['DM POST Test Failure. General POST error', 'CRITICAL'], |
| 54 |
['DM POST NVRAM test failure. Invalid NVRAM content error', 'CRITICAL'], |
| 55 |
['DM POST invalid peer Data Mover type', 'CRITICAL'], |
| 56 |
['DM POST invalid Data Mover part number', 'CRITICAL'], |
| 57 |
['DM POST Fibre Channel test failure. Error in blade Fibre connection', 'CRITICAL'], |
| 58 |
['DM POST network test failure. Error in Ethernet controller', 'CRITICAL'], |
| 59 |
['DM T2NET Error. Unable to get blade reason code due to management switch problems', 'CRITICAL'] |
| 60 |
] |
| 61 |
}; |
| 62 |
|
| 63 |
$self->{components_path} = 'storage::emc::celerra::local::mode::components'; |
| 64 |
$self->{components_module} = ['controlstation', 'datamover']; |
| 65 |
} |
| 66 |
|
| 67 |
sub cmd_execute { |
| 68 |
my ($self, %options) = @_; |
| 69 |
|
| 70 |
($self->{stdout}, my $exit_code) = $options{custom}->execute_command( |
| 71 |
command => 'getreason', |
| 72 |
command_path => '/nas/sbin', |
| 73 |
command_options => '2>&1', |
| 74 |
no_quit => 1 |
| 75 |
); |
| 76 |
|
| 77 |
if ($exit_code != 0 && $exit_code != 255) { |
| 78 |
$self->{output}->add_option_msg(short_msg => "Command error: $self->{stdout}"); |
| 79 |
$self->{output}->option_exit(); |
| 80 |
} |
| 81 |
} |
| 82 |
|
| 83 |
sub new { |
| 84 |
my ($class, %options) = @_; |
| 85 |
my $self = $class->SUPER::new(package => __PACKAGE__, %options, no_absent => 1, no_performance => 1); |
| 86 |
bless $self, $class; |
| 87 |
|
| 88 |
$options{options}->add_options(arguments => { |
| 89 |
}); |
| 90 |
|
| 91 |
return $self; |
| 92 |
} |
| 93 |
|
| 94 |
1; |
| 95 |
|
| 96 |
__END__ |
| 97 |
|
| 98 |
=head1 MODE |
| 99 |
|
| 100 |
Check control stations and data movers status. |
| 101 |
|
| 102 |
Command used: /nas/sbin/getreason 2>&1 |
| 103 |
|
| 104 |
=over 8 |
| 105 |
|
| 106 |
=item B<--component> |
| 107 |
|
| 108 |
Which component to check (default: '.*'). |
| 109 |
Can be: 'controlstation', 'datamover'. |
| 110 |
|
| 111 |
=item B<--filter> |
| 112 |
|
| 113 |
Exclude the items given as a comma-separated list (example: --filter=datamover). |
| 114 |
You can also exclude items from specific instances: --filter=datamover,slot_2 |
| 115 |
|
| 116 |
=item B<--no-component> |
| 117 |
|
| 118 |
Define the expected status if no components are found (default: critical). |
| 119 |
|
| 120 |
=item B<--threshold-overload> |
| 121 |
|
| 122 |
Use this option to override the status returned by the plugin when the status label matches a regular expression (syntax: section,[instance,]status,regexp). |
| 123 |
Example: --threshold-overload='datamover,CRITICAL,^(?!(normal)$)' |
| 124 |
|
| 125 |
=back |
| 126 |
|
| 127 |
=cut |
| 128 |
|