| 1 |
/* |
| 2 |
* Copyright (c) 2016, ARM Limited and Contributors. All rights reserved. |
| 3 |
* |
| 4 |
* SPDX-License-Identifier: BSD-3-Clause |
| 5 |
*/ |
| 6 |
|
| 7 |
#include <assert.h> |
| 8 |
|
| 9 |
#include <arch_helpers.h> |
| 10 |
#include <common/debug.h> |
| 11 |
#include <drivers/delay_timer.h> |
| 12 |
#include <lib/mmio.h> |
| 13 |
|
| 14 |
#include <m0_ctl.h> |
| 15 |
#include <plat_private.h> |
| 16 |
#include <rk3399_def.h> |
| 17 |
#include <secure.h> |
| 18 |
#include <soc.h> |
| 19 |
|
| 20 |
void m0_init(void) |
| 21 |
{ |
| 22 |
/* secure config for M0 */ |
| 23 |
mmio_write_32(SGRF_BASE + SGRF_PMU_CON(0), WMSK_BIT(7)); |
| 24 |
mmio_write_32(SGRF_BASE + SGRF_SOC_CON(6), WMSK_BIT(12)); |
| 25 |
|
| 26 |
/* document is wrong, PMU_CRU_GATEDIS_CON0 do not need set MASK BIT */ |
| 27 |
mmio_setbits_32(PMUCRU_BASE + PMUCRU_GATEDIS_CON0, 0x02); |
| 28 |
|
| 29 |
/* |
| 30 |
* To switch the parent to xin24M and div == 1, |
| 31 |
* |
| 32 |
* We need to close most of the PLLs and clocks except the OSC 24MHz |
| 33 |
* durning suspend, and this should be enough to supplies the ddrfreq, |
| 34 |
* For the simple handle, we just keep the fixed 24MHz to supply the |
| 35 |
* suspend and ddrfreq directly. |
| 36 |
*/ |
| 37 |
mmio_write_32(PMUCRU_BASE + PMUCRU_CLKSEL_CON0, |
| 38 |
BIT_WITH_WMSK(15) | BITS_WITH_WMASK(0x0, 0x1f, 8)); |
| 39 |
|
| 40 |
mmio_write_32(PMUCRU_BASE + PMUCRU_CLKGATE_CON2, WMSK_BIT(5)); |
| 41 |
} |
| 42 |
|
| 43 |
void m0_configure_execute_addr(uintptr_t addr) |
| 44 |
{ |
| 45 |
/* set the execute address for M0 */ |
| 46 |
mmio_write_32(SGRF_BASE + SGRF_PMU_CON(3), |
| 47 |
BITS_WITH_WMASK((addr >> 12) & 0xffff, |
| 48 |
0xffffu, 0)); |
| 49 |
mmio_write_32(SGRF_BASE + SGRF_PMU_CON(7), |
| 50 |
BITS_WITH_WMASK((addr >> 28) & 0xf, |
| 51 |
0xfu, 0)); |
| 52 |
} |
| 53 |
|
| 54 |
void m0_start(void) |
| 55 |
{ |
| 56 |
/* enable clocks for M0 */ |
| 57 |
mmio_write_32(PMUCRU_BASE + PMUCRU_CLKGATE_CON2, |
| 58 |
BITS_WITH_WMASK(0x0, 0xf, 0)); |
| 59 |
|
| 60 |
/* clean the PARAM_M0_DONE flag, mean that M0 will start working */ |
| 61 |
mmio_write_32(M0_PARAM_ADDR + PARAM_M0_DONE, 0); |
| 62 |
dmbst(); |
| 63 |
|
| 64 |
mmio_write_32(PMUCRU_BASE + PMUCRU_SOFTRST_CON0, |
| 65 |
BITS_WITH_WMASK(0x0, 0x4, 0)); |
| 66 |
|
| 67 |
udelay(5); |
| 68 |
/* start M0 */ |
| 69 |
mmio_write_32(PMUCRU_BASE + PMUCRU_SOFTRST_CON0, |
| 70 |
BITS_WITH_WMASK(0x0, 0x20, 0)); |
| 71 |
dmbst(); |
| 72 |
} |
| 73 |
|
| 74 |
void m0_stop(void) |
| 75 |
{ |
| 76 |
/* stop M0 */ |
| 77 |
mmio_write_32(PMUCRU_BASE + PMUCRU_SOFTRST_CON0, |
| 78 |
BITS_WITH_WMASK(0x24, 0x24, 0)); |
| 79 |
|
| 80 |
/* disable clocks for M0 */ |
| 81 |
mmio_write_32(PMUCRU_BASE + PMUCRU_CLKGATE_CON2, |
| 82 |
BITS_WITH_WMASK(0xf, 0xf, 0)); |
| 83 |
} |
| 84 |
|
| 85 |
void m0_wait_done(void) |
| 86 |
{ |
| 87 |
do { |
| 88 |
/* |
| 89 |
* Don't starve the M0 for access to SRAM, so delay before |
| 90 |
* reading the PARAM_M0_DONE value again. |
| 91 |
*/ |
| 92 |
udelay(5); |
| 93 |
dsb(); |
| 94 |
} while (mmio_read_32(M0_PARAM_ADDR + PARAM_M0_DONE) != M0_DONE_FLAG); |
| 95 |
|
| 96 |
/* |
| 97 |
* Let the M0 settle into WFI before we leave. This is so we don't reset |
| 98 |
* the M0 in a bad spot which can cause problems with the M0. |
| 99 |
*/ |
| 100 |
udelay(10); |
| 101 |
dsb(); |
| 102 |
} |