| 1 |
/* |
| 2 |
* Copyright (c) 2015-2018, ARM Limited and Contributors. All rights reserved. |
| 3 |
* |
| 4 |
* SPDX-License-Identifier: BSD-3-Clause |
| 5 |
*/ |
| 6 |
|
| 7 |
#include <platform_def.h> |
| 8 |
|
| 9 |
#include <drivers/arm/nic_400.h> |
| 10 |
#include <lib/mmio.h> |
| 11 |
#include <plat/arm/soc/common/soc_css.h> |
| 12 |
|
| 13 |
void soc_css_init_nic400(void) |
| 14 |
{ |
| 15 |
/* |
| 16 |
* NIC-400 Access Control Initialization |
| 17 |
* |
| 18 |
* Define access privileges by setting each corresponding bit to: |
| 19 |
* 0 = Secure access only |
| 20 |
* 1 = Non-secure access allowed |
| 21 |
*/ |
| 22 |
|
| 23 |
/* |
| 24 |
* Allow non-secure access to some SOC regions, excluding UART1, which |
| 25 |
* remains secure (unless CSS_NON_SECURE_UART is set). |
| 26 |
* Note: This is the NIC-400 device on the SOC |
| 27 |
*/ |
| 28 |
mmio_write_32(SOC_CSS_NIC400_BASE + |
| 29 |
NIC400_ADDR_CTRL_SECURITY_REG(SOC_CSS_NIC400_USB_EHCI), ~0); |
| 30 |
mmio_write_32(SOC_CSS_NIC400_BASE + |
| 31 |
NIC400_ADDR_CTRL_SECURITY_REG(SOC_CSS_NIC400_TLX_MASTER), ~0); |
| 32 |
mmio_write_32(SOC_CSS_NIC400_BASE + |
| 33 |
NIC400_ADDR_CTRL_SECURITY_REG(SOC_CSS_NIC400_USB_OHCI), ~0); |
| 34 |
mmio_write_32(SOC_CSS_NIC400_BASE + |
| 35 |
NIC400_ADDR_CTRL_SECURITY_REG(SOC_CSS_NIC400_PL354_SMC), ~0); |
| 36 |
mmio_write_32(SOC_CSS_NIC400_BASE + |
| 37 |
NIC400_ADDR_CTRL_SECURITY_REG(SOC_CSS_NIC400_APB4_BRIDGE), ~0); |
| 38 |
#if CSS_NON_SECURE_UART |
| 39 |
/* Configure UART for non-secure access */ |
| 40 |
mmio_write_32(SOC_CSS_NIC400_BASE + |
| 41 |
NIC400_ADDR_CTRL_SECURITY_REG(SOC_CSS_NIC400_BOOTSEC_BRIDGE), ~0); |
| 42 |
#else |
| 43 |
mmio_write_32(SOC_CSS_NIC400_BASE + |
| 44 |
NIC400_ADDR_CTRL_SECURITY_REG(SOC_CSS_NIC400_BOOTSEC_BRIDGE), |
| 45 |
~SOC_CSS_NIC400_BOOTSEC_BRIDGE_UART1); |
| 46 |
#endif /* CSS_NON_SECURE_UART */ |
| 47 |
|
| 48 |
} |
| 49 |
|
| 50 |
|
| 51 |
#define PCIE_SECURE_REG 0x3000 |
| 52 |
/* Mask uses REG and MEM access bits */ |
| 53 |
#define PCIE_SEC_ACCESS_MASK ((1 << 0) | (1 << 1)) |
| 54 |
|
| 55 |
void soc_css_init_pcie(void) |
| 56 |
{ |
| 57 |
#if !PLAT_juno |
| 58 |
/* |
| 59 |
* Do not initialize PCIe in emulator environment. |
| 60 |
* Platform ID register not supported on Juno |
| 61 |
*/ |
| 62 |
if (BOARD_CSS_GET_PLAT_TYPE(BOARD_CSS_PLAT_ID_REG_ADDR) == |
| 63 |
BOARD_CSS_PLAT_TYPE_EMULATOR) |
| 64 |
return; |
| 65 |
#endif /* PLAT_juno */ |
| 66 |
|
| 67 |
/* |
| 68 |
* PCIE Root Complex Security settings to enable non-secure |
| 69 |
* access to config registers. |
| 70 |
*/ |
| 71 |
mmio_write_32(SOC_CSS_PCIE_CONTROL_BASE + PCIE_SECURE_REG, |
| 72 |
PCIE_SEC_ACCESS_MASK); |
| 73 |
} |