Debian Codegraph @

include/plat/arm/board/common/v2m_def.h

raw
1 /*
2 * Copyright (c) 2015-2021, ARM Limited and Contributors. All rights reserved.
3 *
4 * SPDX-License-Identifier: BSD-3-Clause
5 */
6 #ifndef V2M_DEF_H
7 #define V2M_DEF_H
8
9 #include <lib/utils_def.h>
10
11 /* Base address of all V2M */
12 #ifdef PLAT_V2M_OFFSET
13 #define V2M_OFFSET PLAT_V2M_OFFSET
14 #else
15 #define V2M_OFFSET UL(0)
16 #endif
17
18 /* V2M motherboard system registers & offsets */
19 #define V2M_SYSREGS_BASE UL(0x1c010000)
20 #define V2M_SYSREGS_SIZE UL(0x00010000)
21 #define V2M_SYS_ID UL(0x0)
22 #define V2M_SYS_SWITCH UL(0x4)
23 #define V2M_SYS_LED UL(0x8)
24 #define V2M_SYS_NVFLAGS UL(0x38)
25 #define V2M_SYS_NVFLAGSSET UL(0x38)
26 #define V2M_SYS_NVFLAGSCLR UL(0x3c)
27 #define V2M_SYS_CFGDATA UL(0xa0)
28 #define V2M_SYS_CFGCTRL UL(0xa4)
29 #define V2M_SYS_CFGSTATUS UL(0xa8)
30
31 #define V2M_CFGCTRL_START BIT_32(31)
32 #define V2M_CFGCTRL_RW BIT_32(30)
33 #define V2M_CFGCTRL_FUNC_SHIFT 20
34 #define V2M_CFGCTRL_FUNC(fn) ((fn) << V2M_CFGCTRL_FUNC_SHIFT)
35 #define V2M_FUNC_CLK_GEN U(0x01)
36 #define V2M_FUNC_TEMP U(0x04)
37 #define V2M_FUNC_DB_RESET U(0x05)
38 #define V2M_FUNC_SCC_CFG U(0x06)
39 #define V2M_FUNC_SHUTDOWN U(0x08)
40 #define V2M_FUNC_REBOOT U(0x09)
41
42 /* NVFLAGS in the V2M motherboard which is preserved after a watchdog reset */
43 #define V2M_SYS_NVFLAGS_ADDR (V2M_SYSREGS_BASE + V2M_SYS_NVFLAGS)
44
45 /*
46 * V2M sysled bit definitions. The values written to this
47 * register are defined in arch.h & runtime_svc.h. Only
48 * used by the primary cpu to diagnose any cold boot issues.
49 *
50 * SYS_LED[0] - Security state (S=0/NS=1)
51 * SYS_LED[2:1] - Exception Level (EL3-EL0)
52 * SYS_LED[7:3] - Exception Class (Sync/Async & origin)
53 *
54 */
55 #define V2M_SYS_LED_SS_SHIFT 0x0
56 #define V2M_SYS_LED_EL_SHIFT 0x1
57 #define V2M_SYS_LED_EC_SHIFT 0x3
58
59 #define V2M_SYS_LED_SS_MASK U(0x1)
60 #define V2M_SYS_LED_EL_MASK U(0x3)
61 #define V2M_SYS_LED_EC_MASK U(0x1f)
62
63 /* V2M sysid register bits */
64 #define V2M_SYS_ID_REV_SHIFT 28
65 #define V2M_SYS_ID_HBI_SHIFT 16
66 #define V2M_SYS_ID_BLD_SHIFT 12
67 #define V2M_SYS_ID_ARCH_SHIFT 8
68 #define V2M_SYS_ID_FPGA_SHIFT 0
69
70 #define V2M_SYS_ID_REV_MASK U(0xf)
71 #define V2M_SYS_ID_HBI_MASK U(0xfff)
72 #define V2M_SYS_ID_BLD_MASK U(0xf)
73 #define V2M_SYS_ID_ARCH_MASK U(0xf)
74 #define V2M_SYS_ID_FPGA_MASK U(0xff)
75
76 #define V2M_SYS_ID_BLD_LENGTH 4
77
78
79 /* NOR Flash */
80 #define V2M_FLASH0_BASE (V2M_OFFSET + UL(0x08000000))
81 #define V2M_FLASH0_SIZE UL(0x04000000)
82 #define V2M_FLASH1_BASE (V2M_OFFSET + UL(0x0c000000))
83 #define V2M_FLASH1_SIZE UL(0x04000000)
84 #define V2M_FLASH_BLOCK_SIZE UL(0x00040000) /* 256 KB */
85
86 #define V2M_IOFPGA_BASE (V2M_OFFSET + UL(0x1c000000))
87 #define V2M_IOFPGA_SIZE UL(0x03000000)
88
89 /* PL011 UART related constants */
90 #define V2M_IOFPGA_UART0_BASE (V2M_OFFSET + UL(0x1c090000))
91 #define V2M_IOFPGA_UART1_BASE (V2M_OFFSET + UL(0x1c0a0000))
92 #define V2M_IOFPGA_UART2_BASE (V2M_OFFSET + UL(0x1c0b0000))
93 #define V2M_IOFPGA_UART3_BASE (V2M_OFFSET + UL(0x1c0c0000))
94
95 #define V2M_IOFPGA_UART0_CLK_IN_HZ 24000000
96 #define V2M_IOFPGA_UART1_CLK_IN_HZ 24000000
97 #define V2M_IOFPGA_UART2_CLK_IN_HZ 24000000
98 #define V2M_IOFPGA_UART3_CLK_IN_HZ 24000000
99
100 /* SP804 timer related constants */
101 #define V2M_SP804_TIMER0_BASE (V2M_OFFSET + UL(0x1C110000))
102 #define V2M_SP804_TIMER1_BASE (V2M_OFFSET + UL(0x1C120000))
103
104 /* SP810 controller */
105 #define V2M_SP810_BASE (V2M_OFFSET + UL(0x1c020000))
106 #define V2M_SP810_CTRL_TIM0_SEL BIT_32(15)
107 #define V2M_SP810_CTRL_TIM1_SEL BIT_32(17)
108 #define V2M_SP810_CTRL_TIM2_SEL BIT_32(19)
109 #define V2M_SP810_CTRL_TIM3_SEL BIT_32(21)
110
111 /*
112 * The flash can be mapped either as read-only or read-write.
113 *
114 * If it is read-write then it should also be mapped as device memory because
115 * NOR flash programming involves sending a fixed, ordered sequence of commands.
116 *
117 * If it is read-only then it should also be mapped as:
118 * - Normal memory, because reading from NOR flash is transparent, it is like
119 * reading from RAM.
120 * - Non-executable by default. If some parts of the flash need to be executable
121 * then platform code is responsible for re-mapping the appropriate portion
122 * of it as executable.
123 */
124 #define V2M_MAP_FLASH0_RW MAP_REGION_FLAT(V2M_FLASH0_BASE,\
125 V2M_FLASH0_SIZE, \
126 MT_DEVICE | MT_RW | MT_SECURE)
127
128 #define V2M_MAP_FLASH0_RO MAP_REGION_FLAT(V2M_FLASH0_BASE,\
129 V2M_FLASH0_SIZE, \
130 MT_RO_DATA | MT_SECURE)
131
132 #define V2M_MAP_FLASH1_RW MAP_REGION_FLAT(V2M_FLASH1_BASE,\
133 V2M_FLASH1_SIZE, \
134 MT_DEVICE | MT_RW | MT_SECURE)
135
136 #define V2M_MAP_FLASH1_RO MAP_REGION_FLAT(V2M_FLASH1_BASE,\
137 V2M_FLASH1_SIZE, \
138 MT_RO_DATA | MT_SECURE)
139
140 #define V2M_MAP_IOFPGA MAP_REGION_FLAT(V2M_IOFPGA_BASE,\
141 V2M_IOFPGA_SIZE, \
142 MT_DEVICE | MT_RW | MT_SECURE)
143
144 /* Region equivalent to V2M_MAP_IOFPGA suitable for mapping at EL0 */
145 #define V2M_MAP_IOFPGA_EL0 MAP_REGION_FLAT( \
146 V2M_IOFPGA_BASE, \
147 V2M_IOFPGA_SIZE, \
148 MT_DEVICE | MT_RW | MT_SECURE | MT_USER)
149
150 #define V2M_MAP_SECURE_SYSTEMREG_EL0 MAP_REGION_FLAT( \
151 V2M_SYSREGS_BASE, \
152 V2M_SYSREGS_SIZE, \
153 MT_DEVICE | MT_RW | MT_SECURE | MT_USER)
154
155 #define V2M_MAP_FLASH0_RW_EL0 MAP_REGION_FLAT( \
156 V2M_FLASH0_BASE, \
157 V2M_FLASH0_SIZE, \
158 MT_DEVICE | MT_RW | MT_SECURE | MT_USER)
159
160 #define V2M_MAP_FLASH1_RW_EL0 MAP_REGION_FLAT( \
161 V2M_FLASH1_BASE, \
162 V2M_FLASH1_SIZE, \
163 MT_DEVICE | MT_RW | MT_SECURE | MT_USER)
164
165 #endif /* V2M_DEF_H */