| 1 |
// -------------------------------------- |
| 2 |
// i2c_scanner |
| 3 |
// |
| 4 |
// Version 1 |
| 5 |
// This program (or code that looks like it) |
| 6 |
// can be found in many places. |
| 7 |
// For example on the Arduino.cc forum. |
| 8 |
// The original author is not known. |
| 9 |
// Version 2, June 2012, Using Arduino 1.0.1 |
| 10 |
// Adapted to be as simple as possible by Arduino.cc user Krodal |
| 11 |
// Version 3, Feb 26 2013 |
| 12 |
// V3 by louarnold |
| 13 |
// Version 4, March 3, 2013, Using Arduino 1.0.3 |
| 14 |
// by Arduino.cc user Krodal. |
| 15 |
// Changes by louarnold removed. |
| 16 |
// Scanning addresses changed from 0...127 to 1...119, |
| 17 |
// according to the i2c scanner by Nick Gammon |
| 18 |
// https://www.gammon.com.au/forum/?id=10896 |
| 19 |
// Version 5, March 28, 2013 |
| 20 |
// As version 4, but address scans now to 127. |
| 21 |
// A sensor seems to use address 120. |
| 22 |
// Version 6, November 27, 2015. |
| 23 |
// Added waiting for the Leonardo serial communication. |
| 24 |
// |
| 25 |
// |
| 26 |
// This sketch tests the standard 7-bit addresses |
| 27 |
// Devices with higher bit address might not be seen properly. |
| 28 |
// |
| 29 |
|
| 30 |
#include <Wire.h> |
| 31 |
|
| 32 |
void setup() { |
| 33 |
Wire.begin(); |
| 34 |
|
| 35 |
Serial.begin(9600); |
| 36 |
while (!Serial); // Leonardo: wait for Serial Monitor |
| 37 |
Serial.println("\nI2C Scanner"); |
| 38 |
} |
| 39 |
|
| 40 |
void loop() { |
| 41 |
int nDevices = 0; |
| 42 |
|
| 43 |
Serial.println("Scanning..."); |
| 44 |
|
| 45 |
for (byte address = 1; address < 127; ++address) { |
| 46 |
// The i2c_scanner uses the return value of |
| 47 |
// the Wire.endTransmission to see if |
| 48 |
// a device did acknowledge to the address. |
| 49 |
Wire.beginTransmission(address); |
| 50 |
byte error = Wire.endTransmission(); |
| 51 |
|
| 52 |
if (error == 0) { |
| 53 |
Serial.print("I2C device found at address 0x"); |
| 54 |
if (address < 16) { |
| 55 |
Serial.print("0"); |
| 56 |
} |
| 57 |
Serial.print(address, HEX); |
| 58 |
Serial.println(" !"); |
| 59 |
|
| 60 |
++nDevices; |
| 61 |
} else if (error == 4) { |
| 62 |
Serial.print("Unknown error at address 0x"); |
| 63 |
if (address < 16) { |
| 64 |
Serial.print("0"); |
| 65 |
} |
| 66 |
Serial.println(address, HEX); |
| 67 |
} |
| 68 |
} |
| 69 |
if (nDevices == 0) { |
| 70 |
Serial.println("No I2C devices found\n"); |
| 71 |
} else { |
| 72 |
Serial.println("done\n"); |
| 73 |
} |
| 74 |
delay(5000); // Wait 5 seconds for next scan |
| 75 |
} |