| 1 |
// I2C SRF10 or SRF08 Devantech Ultrasonic Ranger Finder |
| 2 |
// by Nicholas Zambetti <http://www.zambetti.com> |
| 3 |
// and James Tichenor <http://www.jamestichenor.net> |
| 4 |
|
| 5 |
// Demonstrates use of the Wire library reading data from the |
| 6 |
// Devantech Ultrasonic Rangers SFR08 and SFR10 |
| 7 |
|
| 8 |
// Created 29 April 2006 |
| 9 |
|
| 10 |
// This example code is in the public domain. |
| 11 |
|
| 12 |
|
| 13 |
#include <Wire.h> |
| 14 |
|
| 15 |
void setup() { |
| 16 |
Wire.begin(); // join I2C bus (address optional for master) |
| 17 |
Serial.begin(9600); // start serial communication at 9600 bps |
| 18 |
} |
| 19 |
|
| 20 |
int reading = 0; |
| 21 |
|
| 22 |
void loop() { |
| 23 |
// step 1: instruct sensor to read echoes |
| 24 |
Wire.beginTransmission(112); // transmit to device #112 (0x70) |
| 25 |
// the address specified in the datasheet is 224 (0xE0) |
| 26 |
// but I2C addressing uses the high 7 bits so it's 112 |
| 27 |
Wire.write(byte(0x00)); // sets register pointer to the command register (0x00) |
| 28 |
Wire.write(byte(0x50)); // command sensor to measure in "inches" (0x50) |
| 29 |
// use 0x51 for centimeters |
| 30 |
// use 0x52 for ping microseconds |
| 31 |
Wire.endTransmission(); // stop transmitting |
| 32 |
|
| 33 |
// step 2: wait for readings to happen |
| 34 |
delay(70); // datasheet suggests at least 65 milliseconds |
| 35 |
|
| 36 |
// step 3: instruct sensor to return a particular echo reading |
| 37 |
Wire.beginTransmission(112); // transmit to device #112 |
| 38 |
Wire.write(byte(0x02)); // sets register pointer to echo #1 register (0x02) |
| 39 |
Wire.endTransmission(); // stop transmitting |
| 40 |
|
| 41 |
// step 4: request reading from sensor |
| 42 |
Wire.requestFrom(112, 2); // request 2 bytes from slave device #112 |
| 43 |
|
| 44 |
// step 5: receive reading from sensor |
| 45 |
if (2 <= Wire.available()) { // if two bytes were received |
| 46 |
reading = Wire.read(); // receive high byte (overwrites previous reading) |
| 47 |
reading = reading << 8; // shift high byte to be high 8 bits |
| 48 |
reading |= Wire.read(); // receive low byte as lower 8 bits |
| 49 |
Serial.println(reading); // print the reading |
| 50 |
} |
| 51 |
|
| 52 |
delay(250); // wait a bit since people have to read the output :) |
| 53 |
} |
| 54 |
|
| 55 |
|
| 56 |
/* |
| 57 |
|
| 58 |
// The following code changes the address of a Devantech Ultrasonic Range Finder (SRF10 or SRF08) |
| 59 |
// usage: changeAddress(0x70, 0xE6); |
| 60 |
|
| 61 |
void changeAddress(byte oldAddress, byte newAddress) |
| 62 |
{ |
| 63 |
Wire.beginTransmission(oldAddress); |
| 64 |
Wire.write(byte(0x00)); |
| 65 |
Wire.write(byte(0xA0)); |
| 66 |
Wire.endTransmission(); |
| 67 |
|
| 68 |
Wire.beginTransmission(oldAddress); |
| 69 |
Wire.write(byte(0x00)); |
| 70 |
Wire.write(byte(0xAA)); |
| 71 |
Wire.endTransmission(); |
| 72 |
|
| 73 |
Wire.beginTransmission(oldAddress); |
| 74 |
Wire.write(byte(0x00)); |
| 75 |
Wire.write(byte(0xA5)); |
| 76 |
Wire.endTransmission(); |
| 77 |
|
| 78 |
Wire.beginTransmission(oldAddress); |
| 79 |
Wire.write(byte(0x00)); |
| 80 |
Wire.write(newAddress); |
| 81 |
Wire.endTransmission(); |
| 82 |
} |
| 83 |
|
| 84 |
*/ |