| 1 |
/* |
| 2 |
Digital Pot Control |
| 3 |
|
| 4 |
This example controls an Analog Devices AD5206 digital potentiometer. |
| 5 |
The AD5206 has 6 potentiometer channels. Each channel's pins are labeled |
| 6 |
A - connect this to voltage |
| 7 |
W - this is the pot's wiper, which changes when you set it |
| 8 |
B - connect this to ground. |
| 9 |
|
| 10 |
The AD5206 is SPI-compatible,and to command it, you send two bytes, |
| 11 |
one with the channel number (0 - 5) and one with the resistance value for the |
| 12 |
channel (0 - 255). |
| 13 |
|
| 14 |
The circuit: |
| 15 |
* All A pins of AD5206 connected to +5V |
| 16 |
* All B pins of AD5206 connected to ground |
| 17 |
* An LED and a 220-ohm resistor in series connected from each W pin to ground |
| 18 |
* CS - to digital pin 10 (SS pin) |
| 19 |
* SDI - to digital pin 11 (MOSI pin) |
| 20 |
* CLK - to digital pin 13 (SCK pin) |
| 21 |
|
| 22 |
created 10 Aug 2010 |
| 23 |
by Tom Igoe |
| 24 |
|
| 25 |
Thanks to Heather Dewey-Hagborg for the original tutorial, 2005 |
| 26 |
|
| 27 |
*/ |
| 28 |
|
| 29 |
|
| 30 |
// include the SPI library: |
| 31 |
#include <SPI.h> |
| 32 |
|
| 33 |
|
| 34 |
// set pin 10 as the slave select for the digital pot: |
| 35 |
const int slaveSelectPin = 10; |
| 36 |
|
| 37 |
void setup() { |
| 38 |
// set the slaveSelectPin as an output: |
| 39 |
pinMode(slaveSelectPin, OUTPUT); |
| 40 |
// initialize SPI: |
| 41 |
SPI.begin(); |
| 42 |
} |
| 43 |
|
| 44 |
void loop() { |
| 45 |
// go through the six channels of the digital pot: |
| 46 |
for (int channel = 0; channel < 6; channel++) { |
| 47 |
// change the resistance on this channel from min to max: |
| 48 |
for (int level = 0; level < 255; level++) { |
| 49 |
digitalPotWrite(channel, level); |
| 50 |
delay(10); |
| 51 |
} |
| 52 |
// wait a second at the top: |
| 53 |
delay(100); |
| 54 |
// change the resistance on this channel from max to min: |
| 55 |
for (int level = 0; level < 255; level++) { |
| 56 |
digitalPotWrite(channel, 255 - level); |
| 57 |
delay(10); |
| 58 |
} |
| 59 |
} |
| 60 |
|
| 61 |
} |
| 62 |
|
| 63 |
void digitalPotWrite(int address, int value) { |
| 64 |
// take the SS pin low to select the chip: |
| 65 |
digitalWrite(slaveSelectPin, LOW); |
| 66 |
delay(100); |
| 67 |
// send in the address and value via SPI: |
| 68 |
SPI.transfer(address); |
| 69 |
SPI.transfer(value); |
| 70 |
delay(100); |
| 71 |
// take the SS pin high to de-select the chip: |
| 72 |
digitalWrite(slaveSelectPin, HIGH); |
| 73 |
} |