| 1 |
/* |
| 2 |
SCP1000 Barometric Pressure Sensor Display |
| 3 |
|
| 4 |
Shows the output of a Barometric Pressure Sensor on a |
| 5 |
Uses the SPI library. For details on the sensor, see: |
| 6 |
http://www.sparkfun.com/commerce/product_info.php?products_id=8161 |
| 7 |
http://www.vti.fi/en/support/obsolete_products/pressure_sensors/ |
| 8 |
|
| 9 |
This sketch adapted from Nathan Seidle's SCP1000 example for PIC: |
| 10 |
http://www.sparkfun.com/datasheets/Sensors/SCP1000-Testing.zip |
| 11 |
|
| 12 |
Circuit: |
| 13 |
SCP1000 sensor attached to pins 6, 7, 10 - 13: |
| 14 |
DRDY: pin 6 |
| 15 |
CSB: pin 7 |
| 16 |
MOSI: pin 11 |
| 17 |
MISO: pin 12 |
| 18 |
SCK: pin 13 |
| 19 |
|
| 20 |
created 31 July 2010 |
| 21 |
modified 14 August 2010 |
| 22 |
by Tom Igoe |
| 23 |
*/ |
| 24 |
|
| 25 |
// the sensor communicates using SPI, so include the library: |
| 26 |
#include <SPI.h> |
| 27 |
|
| 28 |
//Sensor's memory register addresses: |
| 29 |
const int PRESSURE = 0x1F; //3 most significant bits of pressure |
| 30 |
const int PRESSURE_LSB = 0x20; //16 least significant bits of pressure |
| 31 |
const int TEMPERATURE = 0x21; //16 bit temperature reading |
| 32 |
const byte READ = 0b11111100; // SCP1000's read command |
| 33 |
const byte WRITE = 0b00000010; // SCP1000's write command |
| 34 |
|
| 35 |
// pins used for the connection with the sensor |
| 36 |
// the other you need are controlled by the SPI library): |
| 37 |
const int dataReadyPin = 6; |
| 38 |
const int chipSelectPin = 7; |
| 39 |
|
| 40 |
void setup() { |
| 41 |
Serial.begin(9600); |
| 42 |
|
| 43 |
// start the SPI library: |
| 44 |
SPI.begin(); |
| 45 |
|
| 46 |
// initialize the data ready and chip select pins: |
| 47 |
pinMode(dataReadyPin, INPUT); |
| 48 |
pinMode(chipSelectPin, OUTPUT); |
| 49 |
|
| 50 |
//Configure SCP1000 for low noise configuration: |
| 51 |
writeRegister(0x02, 0x2D); |
| 52 |
writeRegister(0x01, 0x03); |
| 53 |
writeRegister(0x03, 0x02); |
| 54 |
// give the sensor time to set up: |
| 55 |
delay(100); |
| 56 |
} |
| 57 |
|
| 58 |
void loop() { |
| 59 |
//Select High Resolution Mode |
| 60 |
writeRegister(0x03, 0x0A); |
| 61 |
|
| 62 |
// don't do anything until the data ready pin is high: |
| 63 |
if (digitalRead(dataReadyPin) == HIGH) { |
| 64 |
//Read the temperature data |
| 65 |
int tempData = readRegister(0x21, 2); |
| 66 |
|
| 67 |
// convert the temperature to celsius and display it: |
| 68 |
float realTemp = (float)tempData / 20.0; |
| 69 |
Serial.print("Temp[C]="); |
| 70 |
Serial.print(realTemp); |
| 71 |
|
| 72 |
|
| 73 |
//Read the pressure data highest 3 bits: |
| 74 |
byte pressure_data_high = readRegister(0x1F, 1); |
| 75 |
pressure_data_high &= 0b00000111; //you only needs bits 2 to 0 |
| 76 |
|
| 77 |
//Read the pressure data lower 16 bits: |
| 78 |
unsigned int pressure_data_low = readRegister(0x20, 2); |
| 79 |
//combine the two parts into one 19-bit number: |
| 80 |
long pressure = ((pressure_data_high << 16) | pressure_data_low) / 4; |
| 81 |
|
| 82 |
// display the temperature: |
| 83 |
Serial.println("\tPressure [Pa]=" + String(pressure)); |
| 84 |
} |
| 85 |
} |
| 86 |
|
| 87 |
//Read from or write to register from the SCP1000: |
| 88 |
unsigned int readRegister(byte thisRegister, int bytesToRead) { |
| 89 |
byte inByte = 0; // incoming byte from the SPI |
| 90 |
unsigned int result = 0; // result to return |
| 91 |
Serial.print(thisRegister, BIN); |
| 92 |
Serial.print("\t"); |
| 93 |
// SCP1000 expects the register name in the upper 6 bits |
| 94 |
// of the byte. So shift the bits left by two bits: |
| 95 |
thisRegister = thisRegister << 2; |
| 96 |
// now combine the address and the command into one byte |
| 97 |
byte dataToSend = thisRegister & READ; |
| 98 |
Serial.println(thisRegister, BIN); |
| 99 |
// take the chip select low to select the device: |
| 100 |
digitalWrite(chipSelectPin, LOW); |
| 101 |
// send the device the register you want to read: |
| 102 |
SPI.transfer(dataToSend); |
| 103 |
// send a value of 0 to read the first byte returned: |
| 104 |
result = SPI.transfer(0x00); |
| 105 |
// decrement the number of bytes left to read: |
| 106 |
bytesToRead--; |
| 107 |
// if you still have another byte to read: |
| 108 |
if (bytesToRead > 0) { |
| 109 |
// shift the first byte left, then get the second byte: |
| 110 |
result = result << 8; |
| 111 |
inByte = SPI.transfer(0x00); |
| 112 |
// combine the byte you just got with the previous one: |
| 113 |
result = result | inByte; |
| 114 |
// decrement the number of bytes left to read: |
| 115 |
bytesToRead--; |
| 116 |
} |
| 117 |
// take the chip select high to de-select: |
| 118 |
digitalWrite(chipSelectPin, HIGH); |
| 119 |
// return the result: |
| 120 |
return (result); |
| 121 |
} |
| 122 |
|
| 123 |
|
| 124 |
//Sends a write command to SCP1000 |
| 125 |
|
| 126 |
void writeRegister(byte thisRegister, byte thisValue) { |
| 127 |
|
| 128 |
// SCP1000 expects the register address in the upper 6 bits |
| 129 |
// of the byte. So shift the bits left by two bits: |
| 130 |
thisRegister = thisRegister << 2; |
| 131 |
// now combine the register address and the command into one byte: |
| 132 |
byte dataToSend = thisRegister | WRITE; |
| 133 |
|
| 134 |
// take the chip select low to select the device: |
| 135 |
digitalWrite(chipSelectPin, LOW); |
| 136 |
|
| 137 |
SPI.transfer(dataToSend); //Send register location |
| 138 |
SPI.transfer(thisValue); //Send value to record into register |
| 139 |
|
| 140 |
// take the chip select high to de-select: |
| 141 |
digitalWrite(chipSelectPin, HIGH); |
| 142 |
} |