| 1 |
/**********************************************************/ |
| 2 |
/* Serial Bootloader for Atmel mega8 AVR Controller */ |
| 3 |
/* */ |
| 4 |
/* ATmegaBOOT.c */ |
| 5 |
/* */ |
| 6 |
/* Copyright (c) 2003, Jason P. Kyle */ |
| 7 |
/* */ |
| 8 |
/* Hacked by DojoCorp - ZGZ - MMX - IVR */ |
| 9 |
/* Hacked by David A. Mellis */ |
| 10 |
/* */ |
| 11 |
/* This program is free software; you can redistribute it */ |
| 12 |
/* and/or modify it under the terms of the GNU General */ |
| 13 |
/* Public License as published by the Free Software */ |
| 14 |
/* Foundation; either version 2 of the License, or */ |
| 15 |
/* (at your option) any later version. */ |
| 16 |
/* */ |
| 17 |
/* This program is distributed in the hope that it will */ |
| 18 |
/* be useful, but WITHOUT ANY WARRANTY; without even the */ |
| 19 |
/* implied warranty of MERCHANTABILITY or FITNESS FOR A */ |
| 20 |
/* PARTICULAR PURPOSE. See the GNU General Public */ |
| 21 |
/* License for more details. */ |
| 22 |
/* */ |
| 23 |
/* You should have received a copy of the GNU General */ |
| 24 |
/* Public License along with this program; if not, write */ |
| 25 |
/* to the Free Software Foundation, Inc., */ |
| 26 |
/* 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ |
| 27 |
/* */ |
| 28 |
/* Licence can be viewed at */ |
| 29 |
/* http://www.fsf.org/licenses/gpl.txt */ |
| 30 |
/* */ |
| 31 |
/* Target = Atmel AVR m8 */ |
| 32 |
/**********************************************************/ |
| 33 |
|
| 34 |
#include <inttypes.h> |
| 35 |
#include <avr/io.h> |
| 36 |
#include <avr/pgmspace.h> |
| 37 |
#include <avr/eeprom.h> |
| 38 |
#include <avr/interrupt.h> |
| 39 |
#include <util/delay.h> |
| 40 |
|
| 41 |
//#define F_CPU 16000000 |
| 42 |
|
| 43 |
/* We, Malmoitians, like slow interaction |
| 44 |
* therefore the slow baud rate ;-) |
| 45 |
*/ |
| 46 |
//#define BAUD_RATE 9600 |
| 47 |
|
| 48 |
/* 6.000.000 is more or less 8 seconds at the |
| 49 |
* speed configured here |
| 50 |
*/ |
| 51 |
//#define MAX_TIME_COUNT 6000000 |
| 52 |
#define MAX_TIME_COUNT (F_CPU>>1) |
| 53 |
///#define MAX_TIME_COUNT_MORATORY 1600000 |
| 54 |
|
| 55 |
/* SW_MAJOR and MINOR needs to be updated from time to time to avoid warning message from AVR Studio */ |
| 56 |
#define HW_VER 0x02 |
| 57 |
#define SW_MAJOR 0x01 |
| 58 |
#define SW_MINOR 0x12 |
| 59 |
|
| 60 |
// AVR-GCC compiler compatibility |
| 61 |
// avr-gcc compiler v3.1.x and older doesn't support outb() and inb() |
| 62 |
// if necessary, convert outb and inb to outp and inp |
| 63 |
#ifndef outb |
| 64 |
#define outb(sfr,val) (_SFR_BYTE(sfr) = (val)) |
| 65 |
#endif |
| 66 |
#ifndef inb |
| 67 |
#define inb(sfr) _SFR_BYTE(sfr) |
| 68 |
#endif |
| 69 |
|
| 70 |
/* defines for future compatibility */ |
| 71 |
#ifndef cbi |
| 72 |
#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit)) |
| 73 |
#endif |
| 74 |
#ifndef sbi |
| 75 |
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit)) |
| 76 |
#endif |
| 77 |
|
| 78 |
/* Adjust to suit whatever pin your hardware uses to enter the bootloader */ |
| 79 |
#define eeprom_rb(addr) eeprom_read_byte ((uint8_t *)(addr)) |
| 80 |
#define eeprom_rw(addr) eeprom_read_word ((uint16_t *)(addr)) |
| 81 |
#define eeprom_wb(addr, val) eeprom_write_byte ((uint8_t *)(addr), (uint8_t)(val)) |
| 82 |
|
| 83 |
/* Onboard LED is connected to pin PB5 */ |
| 84 |
#define LED_DDR DDRB |
| 85 |
#define LED_PORT PORTB |
| 86 |
#define LED_PIN PINB |
| 87 |
#define LED PINB5 |
| 88 |
|
| 89 |
|
| 90 |
#define SIG1 0x1E // Yep, Atmel is the only manufacturer of AVR micros. Single source :( |
| 91 |
#define SIG2 0x93 |
| 92 |
#define SIG3 0x07 |
| 93 |
#define PAGE_SIZE 0x20U //32 words |
| 94 |
|
| 95 |
|
| 96 |
void putch(char); |
| 97 |
char getch(void); |
| 98 |
void getNch(uint8_t); |
| 99 |
void byte_response(uint8_t); |
| 100 |
void nothing_response(void); |
| 101 |
|
| 102 |
union address_union { |
| 103 |
uint16_t word; |
| 104 |
uint8_t byte[2]; |
| 105 |
} address; |
| 106 |
|
| 107 |
union length_union { |
| 108 |
uint16_t word; |
| 109 |
uint8_t byte[2]; |
| 110 |
} length; |
| 111 |
|
| 112 |
struct flags_struct { |
| 113 |
unsigned eeprom : 1; |
| 114 |
unsigned rampz : 1; |
| 115 |
} flags; |
| 116 |
|
| 117 |
uint8_t buff[256]; |
| 118 |
//uint8_t address_high; |
| 119 |
|
| 120 |
uint8_t pagesz=0x80; |
| 121 |
|
| 122 |
uint8_t i; |
| 123 |
//uint8_t bootuart0=0,bootuart1=0; |
| 124 |
|
| 125 |
|
| 126 |
void (*app_start)(void) = 0x0000; |
| 127 |
|
| 128 |
int main(void) |
| 129 |
{ |
| 130 |
uint8_t ch,ch2; |
| 131 |
uint16_t w; |
| 132 |
|
| 133 |
//cbi(BL_DDR,BL); |
| 134 |
//sbi(BL_PORT,BL); |
| 135 |
|
| 136 |
asm volatile("nop\n\t"); |
| 137 |
|
| 138 |
/* check if flash is programmed already, if not start bootloader anyway */ |
| 139 |
//if(pgm_read_byte_near(0x0000) != 0xFF) { |
| 140 |
|
| 141 |
/* check if bootloader pin is set low */ |
| 142 |
//if(bit_is_set(BL_PIN,BL)) app_start(); |
| 143 |
//} |
| 144 |
|
| 145 |
/* initialize UART(s) depending on CPU defined */ |
| 146 |
/* m8 */ |
| 147 |
UBRRH = (((F_CPU/BAUD_RATE)/16)-1)>>8; // set baud rate |
| 148 |
UBRRL = (((F_CPU/BAUD_RATE)/16)-1); |
| 149 |
UCSRB = (1<<RXEN)|(1<<TXEN); // enable Rx & Tx |
| 150 |
UCSRC = (1<<URSEL)|(1<<UCSZ1)|(1<<UCSZ0); // config USART; 8N1 |
| 151 |
|
| 152 |
//UBRRL = (uint8_t)(F_CPU/(BAUD_RATE*16L)-1); |
| 153 |
//UBRRH = (F_CPU/(BAUD_RATE*16L)-1) >> 8; |
| 154 |
//UCSRA = 0x00; |
| 155 |
//UCSRC = 0x86; |
| 156 |
//UCSRB = _BV(TXEN)|_BV(RXEN); |
| 157 |
|
| 158 |
|
| 159 |
/* this was giving uisp problems, so I removed it; without it, the boot |
| 160 |
works on with uisp and avrdude on the mac (at least). */ |
| 161 |
//putch('\0'); |
| 162 |
|
| 163 |
//uint32_t l; |
| 164 |
//uint32_t time_count; |
| 165 |
//time_count=0; |
| 166 |
|
| 167 |
/* set LED pin as output */ |
| 168 |
sbi(LED_DDR,LED); |
| 169 |
for (i = 0; i < 16; i++) { |
| 170 |
outb(LED_PORT, inb(LED_PORT) ^ _BV(LED)); |
| 171 |
_delay_loop_2(0); |
| 172 |
} |
| 173 |
|
| 174 |
//for (l=0; l<40000000; l++) |
| 175 |
//outb(LED_PORT, inb(LED_PORT) ^= _BV(LED)); |
| 176 |
|
| 177 |
/* flash onboard LED three times to signal entering of bootloader */ |
| 178 |
//for(i=0; i<3; ++i) { |
| 179 |
//for(l=0; l<40000000; ++l); |
| 180 |
//sbi(LED_PORT,LED); |
| 181 |
//for(l=0; l<40000000; ++l); |
| 182 |
//cbi(LED_PORT,LED); |
| 183 |
//} |
| 184 |
|
| 185 |
/* see comment at previous call to putch() */ |
| 186 |
//putch('\0'); // this line is needed for the synchronization of the programmer |
| 187 |
|
| 188 |
/* forever */ |
| 189 |
for (;;) { |
| 190 |
//if((inb(UCSRA) & _BV(RXC))){ |
| 191 |
/* get character from UART */ |
| 192 |
ch = getch(); |
| 193 |
|
| 194 |
/* A bunch of if...else if... gives smaller code than switch...case ! */ |
| 195 |
|
| 196 |
/* Hello is anyone home ? */ |
| 197 |
if(ch=='0') { |
| 198 |
nothing_response(); |
| 199 |
} |
| 200 |
|
| 201 |
/* Request programmer ID */ |
| 202 |
/* Not using PROGMEM string due to boot block in m128 being beyond 64kB boundary */ |
| 203 |
/* Would need to selectively manipulate RAMPZ, and it's only 9 characters anyway so who cares. */ |
| 204 |
else if(ch=='1') { |
| 205 |
if (getch() == ' ') { |
| 206 |
putch(0x14); |
| 207 |
putch('A'); |
| 208 |
putch('V'); |
| 209 |
putch('R'); |
| 210 |
putch(' '); |
| 211 |
putch('I'); |
| 212 |
putch('S'); |
| 213 |
putch('P'); |
| 214 |
putch(0x10); |
| 215 |
} |
| 216 |
} |
| 217 |
|
| 218 |
/* AVR ISP/STK500 board commands DON'T CARE so default nothing_response */ |
| 219 |
else if(ch=='@') { |
| 220 |
ch2 = getch(); |
| 221 |
if (ch2>0x85) getch(); |
| 222 |
nothing_response(); |
| 223 |
} |
| 224 |
|
| 225 |
/* AVR ISP/STK500 board requests */ |
| 226 |
else if(ch=='A') { |
| 227 |
ch2 = getch(); |
| 228 |
if(ch2==0x80) byte_response(HW_VER); // Hardware version |
| 229 |
else if(ch2==0x81) byte_response(SW_MAJOR); // Software major version |
| 230 |
else if(ch2==0x82) byte_response(SW_MINOR); // Software minor version |
| 231 |
//else if(ch2==0x98) byte_response(0x03); // Unknown but seems to be required by avr studio 3.56 |
| 232 |
else byte_response(0x00); // Covers various unnecessary responses we don't care about |
| 233 |
} |
| 234 |
|
| 235 |
/* Device Parameters DON'T CARE, DEVICE IS FIXED */ |
| 236 |
else if(ch=='B') { |
| 237 |
getNch(20); |
| 238 |
nothing_response(); |
| 239 |
} |
| 240 |
|
| 241 |
/* Parallel programming stuff DON'T CARE */ |
| 242 |
else if(ch=='E') { |
| 243 |
getNch(5); |
| 244 |
nothing_response(); |
| 245 |
} |
| 246 |
|
| 247 |
/* Enter programming mode */ |
| 248 |
else if(ch=='P') { |
| 249 |
nothing_response(); |
| 250 |
// FIXME: modified only here by DojoCorp, Mumbai, India, 20050626 |
| 251 |
//time_count=0; // extend the delay once entered prog.mode |
| 252 |
} |
| 253 |
|
| 254 |
/* Leave programming mode */ |
| 255 |
else if(ch=='Q') { |
| 256 |
nothing_response(); |
| 257 |
//time_count=MAX_TIME_COUNT_MORATORY; // once the programming is done, |
| 258 |
// we should start the application |
| 259 |
// but uisp has problems with this, |
| 260 |
// therefore we just change the times |
| 261 |
// and give the programmer 1 sec to react |
| 262 |
} |
| 263 |
|
| 264 |
/* Erase device, don't care as we will erase one page at a time anyway. */ |
| 265 |
else if(ch=='R') { |
| 266 |
nothing_response(); |
| 267 |
} |
| 268 |
|
| 269 |
/* Set address, little endian. EEPROM in bytes, FLASH in words */ |
| 270 |
/* Perhaps extra address bytes may be added in future to support > 128kB FLASH. */ |
| 271 |
/* This might explain why little endian was used here, big endian used everywhere else. */ |
| 272 |
else if(ch=='U') { |
| 273 |
address.byte[0] = getch(); |
| 274 |
address.byte[1] = getch(); |
| 275 |
nothing_response(); |
| 276 |
} |
| 277 |
|
| 278 |
/* Universal SPI programming command, disabled. Would be used for fuses and lock bits. */ |
| 279 |
else if(ch=='V') { |
| 280 |
getNch(4); |
| 281 |
byte_response(0x00); |
| 282 |
} |
| 283 |
|
| 284 |
/* Write memory, length is big endian and is in bytes */ |
| 285 |
else if(ch=='d') { |
| 286 |
length.byte[1] = getch(); |
| 287 |
length.byte[0] = getch(); |
| 288 |
flags.eeprom = 0; |
| 289 |
if (getch() == 'E') flags.eeprom = 1; |
| 290 |
for (w=0;w<length.word;w++) { |
| 291 |
buff[w] = getch(); // Store data in buffer, can't keep up with serial data stream whilst programming pages |
| 292 |
} |
| 293 |
if (getch() == ' ') { |
| 294 |
if (flags.eeprom) { //Write to EEPROM one byte at a time |
| 295 |
for(w=0;w<length.word;w++) { |
| 296 |
eeprom_wb(address.word,buff[w]); |
| 297 |
address.word++; |
| 298 |
} |
| 299 |
} else { //Write to FLASH one page at a time |
| 300 |
//if (address.byte[1]>127) address_high = 0x01; //Only possible with m128, m256 will need 3rd address byte. FIXME |
| 301 |
//else address_high = 0x00; |
| 302 |
|
| 303 |
//address.word = address.word << 1; //address * 2 -> byte location |
| 304 |
//if ((length.byte[0] & 0x01)) length.word++; //Even up an odd number of bytes |
| 305 |
cli(); //Disable interrupts, just to be sure |
| 306 |
while(bit_is_set(EECR,EEWE)); //Wait for previous EEPROM writes to complete |
| 307 |
asm volatile( |
| 308 |
"clr r17 \n\t" //page_word_count |
| 309 |
"lds r30,address \n\t" //Address of FLASH location (in words) |
| 310 |
"lds r31,address+1 \n\t" |
| 311 |
"lsl r30 \n\t" //address * 2 -> byte location |
| 312 |
"rol r31 \n\t" |
| 313 |
"ldi r28,lo8(buff) \n\t" //Start of buffer array in RAM |
| 314 |
"ldi r29,hi8(buff) \n\t" |
| 315 |
"lds r24,length \n\t" //Length of data to be written (in bytes) |
| 316 |
"lds r25,length+1 \n\t" |
| 317 |
"sbrs r24,0 \n\t" //Even up an odd number of bytes |
| 318 |
"rjmp length_loop \n\t" |
| 319 |
"adiw r24,1 \n\t" |
| 320 |
"length_loop: \n\t" //Main loop, repeat for number of words in block |
| 321 |
"cpi r17,0x00 \n\t" //If page_word_count=0 then erase page |
| 322 |
"brne no_page_erase \n\t" |
| 323 |
"rcall wait_spm \n\t" |
| 324 |
// "wait_spm1: \n\t" |
| 325 |
// "lds r16,%0 \n\t" //Wait for previous spm to complete |
| 326 |
// "andi r16,1 \n\t" |
| 327 |
// "cpi r16,1 \n\t" |
| 328 |
// "breq wait_spm1 \n\t" |
| 329 |
"ldi r16,0x03 \n\t" //Erase page pointed to by Z |
| 330 |
"sts %0,r16 \n\t" |
| 331 |
"spm \n\t" |
| 332 |
"rcall wait_spm \n\t" |
| 333 |
// "wait_spm2: \n\t" |
| 334 |
// "lds r16,%0 \n\t" //Wait for previous spm to complete |
| 335 |
// "andi r16,1 \n\t" |
| 336 |
// "cpi r16,1 \n\t" |
| 337 |
// "breq wait_spm2 \n\t" |
| 338 |
"ldi r16,0x11 \n\t" //Re-enable RWW section |
| 339 |
"sts %0,r16 \n\t" |
| 340 |
"spm \n\t" |
| 341 |
"no_page_erase: \n\t" |
| 342 |
"ld r0,Y+ \n\t" //Write 2 bytes into page buffer |
| 343 |
"ld r1,Y+ \n\t" |
| 344 |
|
| 345 |
"rcall wait_spm \n\t" |
| 346 |
// "wait_spm3: \n\t" |
| 347 |
// "lds r16,%0 \n\t" //Wait for previous spm to complete |
| 348 |
// "andi r16,1 \n\t" |
| 349 |
// "cpi r16,1 \n\t" |
| 350 |
// "breq wait_spm3 \n\t" |
| 351 |
"ldi r16,0x01 \n\t" //Load r0,r1 into FLASH page buffer |
| 352 |
"sts %0,r16 \n\t" |
| 353 |
"spm \n\t" |
| 354 |
|
| 355 |
"inc r17 \n\t" //page_word_count++ |
| 356 |
"cpi r17,%1 \n\t" |
| 357 |
"brlo same_page \n\t" //Still same page in FLASH |
| 358 |
"write_page: \n\t" |
| 359 |
"clr r17 \n\t" //New page, write current one first |
| 360 |
"rcall wait_spm \n\t" |
| 361 |
// "wait_spm4: \n\t" |
| 362 |
// "lds r16,%0 \n\t" //Wait for previous spm to complete |
| 363 |
// "andi r16,1 \n\t" |
| 364 |
// "cpi r16,1 \n\t" |
| 365 |
// "breq wait_spm4 \n\t" |
| 366 |
"ldi r16,0x05 \n\t" //Write page pointed to by Z |
| 367 |
"sts %0,r16 \n\t" |
| 368 |
"spm \n\t" |
| 369 |
"rcall wait_spm \n\t" |
| 370 |
// "wait_spm5: \n\t" |
| 371 |
// "lds r16,%0 \n\t" //Wait for previous spm to complete |
| 372 |
// "andi r16,1 \n\t" |
| 373 |
// "cpi r16,1 \n\t" |
| 374 |
// "breq wait_spm5 \n\t" |
| 375 |
"ldi r16,0x11 \n\t" //Re-enable RWW section |
| 376 |
"sts %0,r16 \n\t" |
| 377 |
"spm \n\t" |
| 378 |
"same_page: \n\t" |
| 379 |
"adiw r30,2 \n\t" //Next word in FLASH |
| 380 |
"sbiw r24,2 \n\t" //length-2 |
| 381 |
"breq final_write \n\t" //Finished |
| 382 |
"rjmp length_loop \n\t" |
| 383 |
|
| 384 |
"wait_spm: \n\t" |
| 385 |
"lds r16,%0 \n\t" //Wait for previous spm to complete |
| 386 |
"andi r16,1 \n\t" |
| 387 |
"cpi r16,1 \n\t" |
| 388 |
"breq wait_spm \n\t" |
| 389 |
"ret \n\t" |
| 390 |
|
| 391 |
"final_write: \n\t" |
| 392 |
"cpi r17,0 \n\t" |
| 393 |
"breq block_done \n\t" |
| 394 |
"adiw r24,2 \n\t" //length+2, fool above check on length after short page write |
| 395 |
"rjmp write_page \n\t" |
| 396 |
"block_done: \n\t" |
| 397 |
"clr __zero_reg__ \n\t" //restore zero register |
| 398 |
: "=m" (SPMCR) : "M" (PAGE_SIZE) : "r0","r16","r17","r24","r25","r28","r29","r30","r31"); |
| 399 |
|
| 400 |
/* Should really add a wait for RWW section to be enabled, don't actually need it since we never */ |
| 401 |
/* exit the bootloader without a power cycle anyhow */ |
| 402 |
} |
| 403 |
putch(0x14); |
| 404 |
putch(0x10); |
| 405 |
} |
| 406 |
} |
| 407 |
|
| 408 |
/* Read memory block mode, length is big endian. */ |
| 409 |
else if(ch=='t') { |
| 410 |
length.byte[1] = getch(); |
| 411 |
length.byte[0] = getch(); |
| 412 |
if (getch() == 'E') flags.eeprom = 1; |
| 413 |
else { |
| 414 |
flags.eeprom = 0; |
| 415 |
address.word = address.word << 1; // address * 2 -> byte location |
| 416 |
} |
| 417 |
if (getch() == ' ') { // Command terminator |
| 418 |
putch(0x14); |
| 419 |
for (w=0;w < length.word;w++) { // Can handle odd and even lengths okay |
| 420 |
if (flags.eeprom) { // Byte access EEPROM read |
| 421 |
putch(eeprom_rb(address.word)); |
| 422 |
address.word++; |
| 423 |
} else { |
| 424 |
if (!flags.rampz) putch(pgm_read_byte_near(address.word)); |
| 425 |
address.word++; |
| 426 |
} |
| 427 |
} |
| 428 |
putch(0x10); |
| 429 |
} |
| 430 |
} |
| 431 |
|
| 432 |
/* Get device signature bytes */ |
| 433 |
else if(ch=='u') { |
| 434 |
if (getch() == ' ') { |
| 435 |
putch(0x14); |
| 436 |
putch(SIG1); |
| 437 |
putch(SIG2); |
| 438 |
putch(SIG3); |
| 439 |
putch(0x10); |
| 440 |
} |
| 441 |
} |
| 442 |
|
| 443 |
/* Read oscillator calibration byte */ |
| 444 |
else if(ch=='v') { |
| 445 |
byte_response(0x00); |
| 446 |
} |
| 447 |
// } else { |
| 448 |
// time_count++; |
| 449 |
// if (time_count>=MAX_TIME_COUNT) { |
| 450 |
// app_start(); |
| 451 |
// } |
| 452 |
// } |
| 453 |
} /* end of forever loop */ |
| 454 |
} |
| 455 |
|
| 456 |
void putch(char ch) |
| 457 |
{ |
| 458 |
/* m8 */ |
| 459 |
while (!(inb(UCSRA) & _BV(UDRE))); |
| 460 |
outb(UDR,ch); |
| 461 |
} |
| 462 |
|
| 463 |
char getch(void) |
| 464 |
{ |
| 465 |
/* m8 */ |
| 466 |
uint32_t count = 0; |
| 467 |
while(!(inb(UCSRA) & _BV(RXC))) { |
| 468 |
/* HACKME:: here is a good place to count times*/ |
| 469 |
count++; |
| 470 |
if (count > MAX_TIME_COUNT) |
| 471 |
app_start(); |
| 472 |
} |
| 473 |
return (inb(UDR)); |
| 474 |
} |
| 475 |
|
| 476 |
void getNch(uint8_t count) |
| 477 |
{ |
| 478 |
uint8_t i; |
| 479 |
for(i=0;i<count;i++) { |
| 480 |
/* m8 */ |
| 481 |
//while(!(inb(UCSRA) & _BV(RXC))); |
| 482 |
//inb(UDR); |
| 483 |
getch(); // need to handle time out |
| 484 |
} |
| 485 |
} |
| 486 |
|
| 487 |
void byte_response(uint8_t val) |
| 488 |
{ |
| 489 |
if (getch() == ' ') { |
| 490 |
putch(0x14); |
| 491 |
putch(val); |
| 492 |
putch(0x10); |
| 493 |
} |
| 494 |
} |
| 495 |
|
| 496 |
void nothing_response(void) |
| 497 |
{ |
| 498 |
if (getch() == ' ') { |
| 499 |
putch(0x14); |
| 500 |
putch(0x10); |
| 501 |
} |
| 502 |
} |
| 503 |
|
| 504 |
/* end of file ATmegaBOOT.c */ |
| 505 |
|
| 506 |
|
| 507 |
|