Debian Codegraph @

SETUP

raw ◀ ▶
Source reconstructed at patch state 0 of 1 — not the installed (fully patched) source.
1 Debian patch touch this file
1 JPEG version 1.2
2
3 1) Printing documentation:
4
5 Documentation is in the PostScript file doc.ps. It is about 50 pages
6 long.
7
8 2) Making the program.
9
10 The makefile should be setup for most UNIX systems as is. Simply type
11 "make" in the source code directory.
12
13 For SYSV only libraries, substitute the first line in the makefile
14 #DEFINES = -DSYSV -DNOTRUNCATE for
15 #DEFINES
16
17 which allows for SYSV libraries to be used instead. The NOTRUNCATE
18 flag avoids the lack of the ftruncate() call used in io.c.
19
20 Caution: For the compilation, the lexer.l file should be older than
21 the lexer.c file otherwise many machines will try and lex the lexer.l
22 file (thus clobbering potentially the lexer.c file). In general, the
23 tar will take out the lexer.l file first (it's specified to do that),
24 so there shouldn't be any problems unless the directory is _copied_
25 and then remade, in which case, the lexer.c file will be older because
26 is lexically of lesser value than lexer.l. This is a potential bug.
27
28 3) Testing the program.
29
30 Two small test files are nonint.jpg and blkint.jpg. If you wish to
31 extract them, type
32
33 jpeg -d -s nonint.jpg
34 jpeg -d -s blkint.jpg
35
36 The resulting files should be in
37
38 nonint.jpg.1 nonint.jpg.2 nonint.jpg.3
39 blkint.jpg.1 blkint.jpg.2 blkint.jpg.3
40
41 These files are raw raster-scan component files 128x128 for the Y
42 (.1), 64x128 for the U(.2) and V(.3).
43
44 4) Displaying the decompressed files.
45
46 The decompressed *.1 *.2 *.3 files may be displayed through the
47 program "cv" which may be obtained by anonymous ftp from
48 havefun.stanford.edu:pub/cv/CVv1.1.tar.Z. If the program is in your
49 current directory search-path, type
50
51 cv -iw 128 -ih 128 nonint.jpg -SF
52
53 or
54
55 cv -iw 128 -ih 128 blkint.jpg -SF
56
57 5) Recompressing the sample files
58
59 Use the following commands to recompress the nonint.jpg.* component
60 files into the nonint.jpg2 file:
61
62 jpeg -iw 128 -ih 128 -n -hf 2 nonint.jpg.1 nonint.jpg.2 nonint.jpg.3 \
63 -s nonint2.jpg
64
65 Use the following commands to recompress the blkint.jpg.* component
66 files into the blkint.jpg2 file:
67
68 jpeg -iw 128 -ih 128 -hf 2 blkint.jpg.1 blkint.jpg.2 blkint.jpg.3 \
69 -s blkint2.jpg
70
71 Surprisingly, recompressing and decompressing the blkint should yield
72 the same result. (The nonint files will not yield the same result -
73 but very close - since the non-interleaved mode defaults to using the
74 LUMINANCE quantization matrix for the first color component of each
75 scan.) See the documentation for more details on other parameters.
76
77 6) Some short interpreted programs for the encoder: (See Chapter 4 of
78 the documentation behind these programs).
79
80 test.huff test.3stream test.q
81