;; USART test ;; ;; The purpose of this program is to verify that gpsim's ;; USART functions properly. The USART module is used to loop ;; characters back to the receiver testing RCIF interupts. ;; ;; ;; list p=16f877 include include __CONFIG _WDT_OFF errorlevel -302 radix dec ;---------------------------------------------------------------------- ; RAM Declarations ; INT_VAR UDATA 0x20 w_temp RES 1 status_temp RES 1 pclath_temp RES 1 ;fsr_temp RES 1 INT_VAR1 UDATA 0xA0 w_temp1 RES 1 ;Alias for w_temp at address 0x20 GPR_DAT UDATA #define RX_BUF_SIZE 0x10 temp1 RES 1 temp2 RES 1 temp3 RES 1 tx_ptr RES 1 rxLastByte RES 1 rxFlag RES 1 ;---------------------------------------------------------------------- ; ********************* RESET VECTOR LOCATION ******************** ;---------------------------------------------------------------------- RESET_VECTOR CODE 0x000 ; processor reset vector movlw high start ; load upper byte of 'start' label movwf PCLATH ; initialize PCLATH goto start ; go to beginning of program ;------------------------------------------------------------------------ ; ; Interrupt Vector ; ;------------------------------------------------------------------------ INT_VECTOR CODE 0x004 ; interrupt vector location movwf w_temp swapf STATUS,w clrf STATUS movwf status_temp movf PCLATH,w movwf pclath_temp clrf PCLATH bcf STATUS,RP0 btfsc INTCON,PEIE btfss PIR1,RCIF goto int_done ;;; Received a Character .assert "rcreg == txreg, 'sent character looped back'" nop movf RCREG,W movwf rxLastByte bsf rxFlag,0 int_done: clrf STATUS movf pclath_temp,w movwf PCLATH swapf status_temp,w movwf STATUS swapf w_temp,f swapf w_temp,w retfie ;; ---------------------------------------------------- ;; ;; start ;; MAIN CODE start .sim ".frequency=10e6" .sim ".xpos = 48" .sim ".ypos = 36" .sim "break c 0x100000" .sim "module library libgpsim_modules" .sim "module load usart U1" .sim "U1.xpos = 240" .sim "U1.ypos = 204" .sim "node PIC_tx" .sim "node PIC_rx" ;; Tie the USART module to the PIC .sim "attach PIC_tx portc6 U1.RXPIN" .sim "attach PIC_rx portc7 U1.TXPIN" ;; Set the USART module's Baud Rate .sim "U1.txbaud = 4800" .sim "U1.rxbaud = 4800" .sim "U1.loop = true" ;; USART Initialization ;; ;; Turn on the high baud rate (BRGH), disable the transmitter, ;; disable synchronous mode. ;; clrf STATUS bsf PORTC,6 ;Make sure the TX line drives high when ;it is programmed as an output. bsf STATUS,RP0 bsf TRISC,7 ;RX is an input bcf TRISC,6 ;TX is an output ;; CSRC - clock source is a don't care ;; TX9 - 0 8-bit data ;; TXEN - 0 don't enable the transmitter. ;; SYNC - 0 Asynchronous ;; BRGH - 1 Select high baud rate divisor ;; TRMT - x read only ;; TX9D - 0 not used movlw (1< 9 bits ; and < 10 bits or between 1.872 and 2.08 msec. ; with oscillator at 10MHz and TMR0 / 64 expect between 73 and 81 ; TMR0 cycles. Or 146 - 162 for 2 characters movf TMR0,W .assert "tmr0 > 146 && tmr0 < 162, '*** FAILED baud rate'" nop clrf rxFlag call rx_loop .assert "(pir1 & 0x10) == 0x10, '*** FAILED TXIF low double send'" nop done: .assert "'*** PASSED Usart with PIR1V2'" goto $ TransmitNextByte: clrf rxFlag call tx_message btfss PIR1,TXIF goto $-1 movwf TXREG rx_loop: btfss rxFlag,0 goto rx_loop return tx_message incf tx_ptr,w andlw 0x0f movwf tx_ptr addlw TX_TABLE skpnc incf PCLATH,f movwf PCL TX_TABLE dt "0123456789ABCDEF",0 delay decfsz temp1,f goto $+2 decfsz temp2,f goto delay return end