2006-08-19 JoeB: * There is something inconsistent about SAVEDEGREE versus DEGREEPRINTOUTPUT. I suspect that the former is mistakenly investigated instead of the latter, in e. g. GROEBNERFINISH. * The GLOBAL variable !#!$NoHigherGbRedNeeded!* either should be put into use (by adding a new minor strategy mode), or removed. 2006-08-18 JoeB: * In 'real and true' commutative TDEGREVLEX order, with non-homogeneous input, the refined Buchberger criterion does not work. There may be subsequent monomials, which are lower in the most significant variable than is the LeadMon, but which still are lower, because their totaldegrees are. Thus, it is not sure that the power of this variable in the LeadMon also is a factor of the entire polynomial. 2006-08-09 JoeB, VU: * Make MAXDEG inhibition of calculation of higher critical pairs efficient. (Now, seemingly, the calculated but discarded pairs clutter the heap.) 2006-08-08 JoeB: * ReducePol (nowadays, at least) returns a genaugredor, NOT a genaugredand! Before changing the protocol, go through the situation a little further. However, I call PreenRedand on the result of ReducePol, in FixNGbe; and it is NOT ALWAYS a noop. (Formerly, the Redand2Redor wasn't performed until FixGbe was applied on all current degree new Gbe's simultaneously, at the end of the calculations for this degree.) * Refine RABBIT mode settings: SETRABBIT, GETRABBIT. 2006-08-07 JoeB: * The SAWS mode incopatibilities now are extended, by NOT making AUTOREDUCEINPUT and e.g. AutoReduceFromTo working in itemwise mode. Probably rather extensive testing is necessary to get SAWS working in ANY mode! 2006-08-06 JoeB: * MONFACTORP is ONLY used as a boolean, but in the non-commutative case does MUCH more. 2006-08-05 JoeB: * DestructRedor2Redand is sometimes defined as NILNOOPFCN1, sometimes as IBIDNOOPFCN. The former seems most in accordance with the documentation. * The manual documents nowadays non-existing procedures; at least POLALGOUT. Define them, with obsoleteness warnings! 2005-06-25 JoeB, VU: * It should be possible to stop ANICK at a certain homological degree (altough we go on in totaldegree). Something like SETMAXHOMDEGREE? * We should add a dynamic way to add new monoid orders. In this context, some calculation of a new commutative monomial quotient could be useful. 2005-06-21 VU: * Autosave mode; able to restart calculation after a chrash. Must be coupled with "restore" and "continue". We have to save the following monomials: Leading ones in Groebner basis elements; those in S-polynomials. 2005-07-16 JoeB, VU: * If e.g. we (in this order) call ANICK, SETNORESOLUTION, and ANICK again, the second call to ANICK does not work. The reason is that only when the anick module is loaded the setup changes are made. One remedy of course could be to move the settings to the beginning of call of ANICK; or to make them explicitly, if ANICKISLOADED. However, this might lessen the flexibility a little. * Fix the output mode default in such a way that algebraic output is standard, when outvars are set. Perhaps a new, flexible mode; or just changing the default setting? 2005-07-15 JoeB: * There are situations where partial results are not exhibited, since no call to FLUSHCHANNEL was included. This seems to be the case in the anick module; and probably in some other cases, where the SC&VU test suite did not produce (complete) output. Insert them! * Include tests of positive characteristics. Correct such clisp compilation as is set up without proper macros inserted. 2005-02-19 JoeB: * If such do not exist, then define procedures for adding to, but not replacing, InPols. Say, ADDLISPFORMINPUT and ADDALGFORMINPUT; the latter NOT accepting a vars statement. DONE in v. 0.988/JoeB 2005-01-19 JoeB: * The customising procedures should have alternatives working as hooks rather than supplanting the calling procedures. We may also want interruptions (pausing with the possibility of performing a number of dialogue or lisp commands, but possibility to resume calculations), breaking (to top level, possibly by creating an error), and quitting (which is simple to do by means of QUIT). Hooks could be created by separate procedures, or by letting a `reserved' identifier as return value cause `hooking', i.e., continuation with the rest of the calling procedure. 2004-10-12 JoeB , VU: * (noncommify)(simple)vars x,y;x*y-y^2; yields heap overflow already at degree 99. Why? If in addition the Hilbert series limitation is active, with the limitations set to the true Hilbert series (by means of setting the DEFAULT to (PLUS2 HSDEG 1)), and (of course) PBSERIES is ON, then the run seems to be markedly slower; and it collapses by heap overflow already at degree 80 (approximately). Again, why? * Check the action of POSLEADCOEFFS. UnSign-ing seems to be automatic in the SparseContents submode, but not at all 'activatible' by modes or switches in the dense case. I think I removed these troubles a long time ago. Perhaps, it is done in e.g. DenseContentChar0SubtractRedand1, in some oldfashioned variant. To-day, UNSIGNLC!'S is called explicitly by aninterf.sl procedures (ultimately called by ResolutionFixcDegEnd); but no-where else. 2004-09-30 JoeB , VU: * Fix merging of doc's from rather different sources. Some rather old doc's contain things never added to the newer ones. * Investigate precisely what troubles may arise from running inhomogeneous input. Write one or several strategies for doing this properly. At least one of these should be compatible with ELIM orderings. * Re-organise the "safe" stuff into the mode handling. Include handling of constant terms. * Incorporate corrections from older versions (???) (alternatively: find and eliminate brand new bugs) concerning repeated series calculation and inner embdim (which seemingly is not quite cleared even by CLEARRING). * Check and update SAWS. * Make a manual version in a `booklet printable' form. DONE circa 2005-06-15 by SV & VU. * Investigate, possibly write new, procedures for solving linear equations. * Employ the latter in calculating rational Hilbert series in the non-commutative case. 2004-05-04 JoeB: * Enter more `free floating' modes into the compact mode handler. This includes: SAWS modifications; MODULE or TWOMODULES module variable numbers; homogeneity. * Fix the common lisp independence of compile.sl et cetera. 2003-11-01 JoeB: Common Lisp now have troubles with lambda expressions. I am not sure of how to overcome this, but I have a memory that we found some (partial?) remedies earlier. This touches the new FINDMODECLASHES family of procedures (by means of ModeSettingP), and also employing the procedure alternative for argument to SETHSERIESMINIMUMDEFAULT. 2003-10-29 JoeB: (* Checksetup: E.g., modules do not work within the commutative case now. Add some "Incompatibilities checker". DONE 2004-05-04.) * The DIALOGUE is rather underdeveloped. Test its clisp abilities, inter alia! (* CLEARIDEAL removes the variable number information. This should not be so. On the other hand, a new CLEARRING might do this - and much more. [FIXED 2003-11-01] ) 2003-08-28 JoeB: * Move (at least the source files of) the new run test files from bin/Linux_elf to tests. * Merge the loose pieces of documentation - such as ReadMe and ReadMe0.91.var (with info on log files); KnownBugs and known.bugs; News, ... . * Make a 'make' based version of mkbergman. 2003-08-18 JoeB: Fix the linear and constant input problems by adding a new mode difference. Some efficient procedures be replaced by safer ones, when linear or constant inputs are acceptable. (May or may not be ord/altweights dependent, simultaneously.) Affected procedures include: LC2, ALGFORMINPUT (or one of its auxiliaries), 2002-10-09 JoeB: Check why (nc) FixNGbe collapses with linear input. 2002-06-28 JoeB: Move setting of EMBDIM from PBINIT to noncommMonomialInit ... and replace it perhaps by !&!*InnerEmbDim!&!* setting, like in commMonomialInit? Problem, of course: We may do calculations with embdim unset, if PB is off, but not if it is on. Thus perhaps: Make a tentative setting in noncommMonomialInit, and an obligatoric one (if not yet set) in PBSERIES. Also, unset !&!*InnerEmbDim!&!* in case of clearing the variables. Actually, this should perhaps be reset when variables are? 1999-11-26 JoeB: Make the last argument to mkbergman in unix environments facultative; using cd $0 and an adequate cd ../.. ... /.. in order to get to the bmroot and $cwd extract it (at a suggestion from SV). However, warn for the use of this alternative! Check if caseconv now is OK, so that one may apply it even when the xsrc and xauxil directories did exist. 1999-06-28 JoeB: Make the HSERIESMIN procedures self-loading. Introduce CLEARing of hseriesminima. Make setting hseriesmin strategy to load hseries (if not done). 1999-06-27 JoeB: According to SV, the single instance of a case non-distinction potential name clash would be noncommMonTimes2 versus noncommMONTIMES2 (in ncmonom.sl). Perhaps should rename one of them, in order to facilitate for others to adapt the bm sources in other settings? 1997-10-12 JoeB: Add ncCALCPOLRING (or better ncCALCFREERING), which sets INVHILBERTSERIES appropriately, and which in the same cases as in the next note calculates HILBERTSERIES up to MAXDEG. 1997-10-12 ufn: Suggestion: if Maxdeg was greater than obtained maximum degree in GB, continue to calculate Hilbert(Poincare)series untill Maxdeg. 1997-09-18 JoeB: Fix weight setting and variable setting in such ways that they are consistent from the user point of view. If necessary, distinguish internal weight lists and dplists from interface forms. 1997-09-08 JoeB: Fix the non-comm exponent output. Introduce new modifications: a PRINTEXPONENTS flag (default: T); flag deciding whether the exponents be collected or spread. DONE 09-18 And a flag or mode setter deciding whether the first or the last variable be the highest in standard orders. 1997-08-27 JoeB: DOCUMENT setweights. Add getweights, clearweights, printweights. Make it compatible with series calculation, Anick, stagger, (de)homogenisation. Make (de)homogenisation variants in the non-commutative case. Write the file output checker. 1997-08-15: JoeB: Either include YESP in slext.sl, or exclude it from the module series procedures. 1997-05-22: JoeB: Investigate if the AddTo!&Char0Lists calls in stg.sl for AutoReduceFix, StagFormSPol, ReduceSubstantialPol, and STAGGERFINISH are adequate. 1997-04-09: JoeB: Fix a nice and neat way of calculating pbseries etc. to a given degree; and DOCUMENT this!! 1997-04-07: JoeB: Remove the Char2RedorMonMult definition (or rather, replace the Char0 one by this). I also seem to have started replacing DestructRedandTermPlus by DestructQPolTermPlus, but I have not completed this? 1997-03-03: JoeB: Check through files outside Char0 for definitions of or occurrences of Char0FOO variants. I believe that RETURNING to Char0 might not work now; it should be fixed as above, and by making ALL FOO-out-of-Char0 initiations at the end of char0.sl, by a call to RESTORECHAR0, if possible. 1996-12-17: Jan S & Ralf: Add possibility to INPUT H series as numerator + denominator degree. 1996-12-09: Ralf: Add (at least) the orders you wish to use at elimination problems: block orders with specific variables (of various degrees); 2 degrevlex blocks being enough. In a Hilbert series driven algorithm, add Moreno's 'criterium' (optionally): If a reduction leads to 0 in the beginning, then they mostly continue in the same manner. Thus, skip such calculations. If not all new Gbe's which should be there are found, in a new pass calculate them to the bitter end. 1996-11-28 Ralf: Imitate Gotzmann? (Dynamically calculate several series, for to see if by Gotzmanns theorem no more should be calculated.) Likewise, if 0 reached, interrupt! 1996-11-27: - Fix stagger as `proper' and revertible mode. (Fix stagsubs.sl accordingly.) - Fix file and dynamic prime logarithm table making. - Fix `generic' system saver (in slext.sl). - Integrate the newdomain content into other souce files. - Integrate comm and nc series handling. (Should sermul be integrated, too?) (Hilbert series driven algorithms included.) - Set up proper modes for anick. - Collect documentation from various sources (incl. Lund and ~sanya). Integrate it, on the doc area. - Make easy-to-access handling of several rings, G-bases, series, et cetera simultaneously. Most of this should be in the version 1.0! The following probably should wait: - Adopt bergman to the latest Psl and Reduce versions. - Set up proper modes for (V.U. and S.C.) module Gbases et cetera. - Make easy-to-access handling of several rings, G-bases, series, et cetera simultaneously. - Make a general command interpreter tool; to be used in alginput, and as a base of a `macaulay-like' interpreter. - Make bergman available with Common Lisp. - Possibly, make bergman available with C. - Trace strategic submode mode /JoeB