#!/bin/bash # avr-evtd Event script # # Sample Event Script written by Bob Perry # NOTE: No longer syncronous with avr-evtd process: maybe more than # one instance of this script running # # Enters via the avr-evtd daemon with the following command options: # 0 - Special event following double press of the 'red' reset button # 1 - AVR device has requested a halt due to error # 2 - Shutdown request from timed shutdown logic # 3 - User has released the power button # 4 - User has pressed the power button # 5 - User has released the 'red' reset button # 6 - User has pressed the reset button # 7 - User has held the power button > 3 seconds # 8 - User has held the reset button > 3 seconds # 9 - Disk used beyond DISKCHECK% # F - Fan failure event, fan stopped for > FANSTOP seconds # E - User selected EM-Mode # S - Five minute shutdown warning event # D - Error message handler DEVICE=$2 PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/sbin tag=avr-daemon facility=user.info # # Populate the configured settings # if [ -f /etc/default/avr-evtd ]; then . /etc/default/avr-evtd fi if [ "$DEBUG" = "ON" ] && [ -d "$LOG" ]; then echo "`date` command is $1[$3] for $DEVICE" >> $LOG/avr-evtd.log fi case "$1" in 0) case "$3" in 1) # Indicate this mode by flashing the DISK FULL LED echo -n "YYYY" > $DEVICE # Add an EM IP address or if no ethernet, start it up FAIL=1 route -n | grep -q eth0 && FAIL=0 if [ "$FAIL" -eq 0 ]; then FAIL=1 route -n | grep -q 192.168.11.0 && FAIL=0 if [ "$FAIL" -eq 1 ]; then ifconfig eth0:EM 192.168.11.150 netmask 255.255.255.0 up fi else /sbin/ifup --force -a -i /etc/avr-evtd/emergency-eth0 sleep 1 route add -net 192.168.11.0 netmask 255.255.255.255.0 eth0:EM fi if [ -e /sbin/utelnetd ]; then utelnetd -p 1234 -l /bin/bash & if [ -e /etc/init.d/apservd ]; then chmod +x /etc/init.d/apservd /etc/init.d/apservd start fi fi ;; 3) # Flash more lights to indicate we are desperate echo -n "SSSS" > $DEVICE if [ ! -e /etc/passwd.em ]; then cp -f /etc/passwd /etc/passwd.em ; fi if [ ! -e /etc/shadow.em ]; then cp -f /etc/shadow /etc/shadow.em ; fi if [ ! -e /etc/group.em ]; then cp -f /etc/group /etc/group.em ; fi if [ ! -e /etc/gshadow.em ]; then cp -f /etc/gshadow /etc/gshadow.em ; fi if [ ! -e /etc/issue.net.em ]; then cp -f /etc/issue.net /etc/issue.net.em ; fi tar xvf /etc/avr-evtd/recovery.tar ;; *) exit -2 ;; esac ;; 3) echo -n "[avr-evtd]: Power Button Up" ;; 4) echo -n "[avr-evtd]: Power Button Down" ;; 5) echo -n "[avr-evtd]: Reset Button Up" ;; 6) echo -n "[avr-evtd]: Reset Button Down" ;; 1|2|7) echo -n "[avr-evtd]: Shutdown" echo -n "]]]]EEEE" > $DEVICE # Perform shutdown request shutdown -h now ;; 8) echo -n "[avr-evtd]: User demanded reset" echo -n "]]]]CCCC" > $DEVICE # Perform reboot reboot ;; 9) if [ "$3" -eq 0 ]; then echo -n "[avr-evtd]: Disk usage now safe" else echo -n "[avr-evtd]: Disk used $3% > Monitored $DISKCHECK%" fi ;; E) echo -n "[avr-evtd]: EM mode selected" if [ "$EMMODE" = "YES" ]; then # Determine flash block to use, default to 2 if [ -f /proc/mtd ]; then MTD=`cat /proc/mtd | grep mtd_status` BLOCK_ID=${MTD:3:1} if [ -z "$BLOCK_ID" ]; then BLOCK_ID=2 ; fi FLASH=/dev/mtdblock$BLOCK_ID else ls -al /dev/fl3 | grep -q "250,[ ]*3" && FLASH=/dev/fl3 fi # Flash device available? if [ -n "$FLASH" ]; then # Check we are dealing with a buffered device? if [ ! -b $FLASH ]; then echo "$FLASH device does not exist, no EM-Mode available" >&2 else DUMP=`cat $FLASH` STATE=${DUMP:2:4} # Check state is currently NORMAL if [ "$STATE" = "OKOK" ]; then echo -n "NGNGNG" > $FLASH fi echo -n "]]]]CCCC" > $DEVICE /sbin/reboot fi fi fi ;; F) echo -n "[avr-evtd]: Fan failure detected" if [ "$3" -eq 0 ]; then logger -p user.emerg -i 'AVR Detected fan fault' fi if [ "$3" -eq 4 ]; then # Illuminate relevant LED and wait for AVR halt message echo -n "iiii" > $DEVICE fi ;; S) if [ "$3" -gt 100 ]; then MESSAGE="System shutdown in less than 5 minutes" else MESSAGE="Shutdown delayed by $3 minutes" fi # Produce relevant message logger -p user.emerg -i $MESSAGE ;; D) MESSAGE="[$3] Error with configuration file" logger -t $tag -p $facility -i $MESSAGE ;; *) exit 1 ;; esac exit 0